Nissan Altima

What is necessary to replace the drive belt idler pulley on a 2000 Nissan Altima?

678

Top Answer
User Avatar
Wiki User
Answered
2006-09-12 03:49:47
2006-09-12 03:49:47

When It no longer hold proper tension if the belt is squeaking then it is probably time to change it

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


how to remove a power steering pulley on a 1997 Nissan altima


The 2005 Nissan Altima auto tensioner pulley can be removed by removing the center bolt. You will need to hold the pulley stationary while you loosen the bolt.


replace 1996 nissan 200sx se 1.6 tension pulley



Just turn the bolt against clockwise and it will come out easily ...


To replace the belt on a Nissan Frontier, first loosen the idler pulley of the belt and remove the bolts. Then slip the replacement belt onto the pulley and put back the bolts.



3 bolts above your oil filter may have to move belt a


ca20? remove all the belts, water pump pulley, underdrive pulley, timing chain cover and timing belt and the water pump is accessible. I would replace the timing belt too.


You will need a small gear puller to do this. They make one that is smaller than a conventional gear puller (for removing crankshaft pulley/dampers) because the clearance behind the damper is a little thin between the pulley and the block. Try NAPA or AutoZone. AutoZone may have them in a blister pack on display.


The water pump on a 97 Nissan Sentra is behind the timing belt. To replace it you will need to drain the coolant, remove the cylinder head, loosen pulley bolts, drive belts, and water pump pulley. Next, remove coolant hoses, water pump bolts, and finally the old water pump. Reverse directions to replace with new pump.



it is time to change bearing on that pulley


The tension pulley should have a bolt that holds it on, allowing you to replace the unit.


Take off the sockets and remove the pump pulley.


Remove the old, damaged idler pulley and replace it with a new one.



There is either a tensioner or an adjustment screw on a pulley. A Haynes manual or Chiltons manual will help with the routing of the belt, and how to adjust the belt tension as well. Usually the idler pulley is used, before loosening the top bolt , loosen the center bolt of the pulley.


The 1996 Nissan Maxima timing marks can be found on the main pulley, on the front of the engine. The timing marks will be scattered around the outside of the pulley.


my husband just did so. the pulley is part of the air condition compressor, so you have to replace the whole part that's connected to the pulley, you can'tjust replace the pulley it self, and going to the junk yard for these partsis very cheap and the way to go.


Take off belt, remove bolt in center of pulley, replace with new pulley (comes with bearing). Reverse to install Take off belt, remove bolt in center of pulley, replace with new pulley (comes with bearing).


The idler pulley on a 2003 Nissan Sentra 1.8 is changed by removing the engine accessories, removing the drive belts, and loosening the retaining bolt. The pulley can then be removed from the vehicle and a new one bolted into place.


Lift car on jack stands, remove right wheel for better access,remove any belts, remove pulley bolt, then use a pulley remover to remove pulley, carefully pry out old seal thebn tap in new seal with mallet or plastic hammer, if pulley has ridges on it you may have to replace pulley or you might still have leaks. reinstall pulley,bolt, belts and wheel. Good Luck.


Call the parts store. They will be able to tell you if the pulley is available separately or not.


what pulley/ there are only about 7 or so on a vehicle. water pump, alternator, ac, power steering pulley



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.