It is real easy. It took me about 45 minutes to replace the starter on a 1990 Maxima GXE.Disconect the negative battery cable on the battery. Put emergency brake on and put car in park.Jack the driver side of the car up and secure with a jack stand or use car ramps.Loosen the shrowd underneeth the front of the car (3or 4 screws)so you can get to the starterLocate starter and disconect the solinoid wire from the positive battery cable.disconect the 2 bolts holding the starter in place.Remove starter.Inspect the teeth on the starter for wear.Inspect the teeth on the flywheel for wear.Install the new replacement starter and secure with the 2 bolts.Connect the solinoin wire to the positive battery cable.Attach the negative battery cable to the battery.That's it.
What type of transmission fluid needed for 2006 nissan maxima
what parts needed to tuneup 1995 nissan maxima
I actually have a brand new blower motor for a 2002 Nissan maxima. Its brand new, I bought it from Sandy Sansing Nissan in Pensacola, Florida thinking I needed to replace it, but it was actually my fan control amplifier that needed replacing. So if you need a new blower motor, I can ship you a new one for a bargain. I paid 219.00 for it, I'll let it go for 100.00. Email me at email@example.com
1 - simplest and cheapest method- replace the axle 2- replace the CV joints and boots 3- lots of unnecessary work, very expensive - check the joints and replace as needed, replace boots
how many gaskets and which ones are needed when you replace the knock sensor on a Nissan frontier w/a 3.3l v6 engine?
if its completely empty should take about 3 pounds
4 to fill it ,unless its been rebuilt then 13 will be needed
Replace the hood shocks.
disconnect your battery. Remove your starter from under your truck and on the top of the starter is the soleniod. unbolt it, and bolt on your new one. Make sure that the spring and the teeth line up on the starter. replace pos. cable if needed. reinstall starter. Check all your other cables to make sure that they are ok. Later
A Vauxhall Asta starter motor will cost about 300 dollars. It will also cost about 50 dollars for labor if that service is needed.
disconnect neg. battery cable ,remove pos.cable from starter .10 or 12 mm wrench.remove wire from starter ,no wrench needed,its a male to female connector,remove 2 bolts holding starter to engine,12 or 14 mm wrench,thats it.
Yes, check the connection to the starter and the spark plug wires first and replace if needed.
Hello, if you want to install a Bose CD cassete in a 97 Nissan Maxima you will need to rewire the sound system in your car in order to have a wiring as required by Bose systems. Non Bose systems don't have the "finesse" that Bose systems have, that is, Bose systems requires shielded wires and cables to carry electrical signals to the amplifyers, that usually are disposed one per speaker in the 97 Maxima. Bose systems are very sensitive and have some relays and things like that to command the premium sound quality in the vehicle. It takes into account even the surface of the seats. The most important is: if you want to put a Bose system in your 97 Nissan Maxima, please find the speakers and the amps for the 97 Nissan Maxima, not from other Bose car system, as it will not work properly. Bose systems are specific design for a specific car. The first thing you can do is to go to phatg20.com and download the Nissan Maxima Factory Service Manual to see the wiring scheme, get the cables and speakers and amps and hands on work. Good luck.
My understanding is that to replace with refills - the dealer can do that. If you go aftermarket - you will replace the wiper arm - two different sizes needed, driver and passenger(28",17").
Depending on where you live, you MAY be able to find a local auto parts retailer that has the ability to test your alternator. They generally test the entire charging system and do not charge for the service since they're trying to get you to buy parts from them. You're right to not trust the dealer, their mechanics are paid partially by commission and tend to want to replace as many parts as they can.
i would replace fan relay, before replacing thermostat. the relay acts as a thermostat for the fan, turning fan on and off when needed
Certainly. Once the engine is running the starter is not needed.
There is no adjustment for the starter clutch. If it isn't worknig properly you replace the rollers, springs and other parts as needed.
the only tools need are a 17 inch socket a rachet a "C" clamp to push the piston back in.
it has to want to change, forcing a change may do more harm than good... everyone should have a manual for their vechicle, and the library should have a professional shop manual available in the reference section for FREE to make copies of--the PRO manual has more detailed info, and may have wiring diagrams when needed...read up and fix 'em like a PRO...good luck Dave :)
your starter Pokemon
The Lucas Upper Cylinder and Injector cleaner is versatile on all cars with fuel injectors. It is also referred to as "Tune-Up in a Bottle." Use every 2-3 months at most or more if needed.
Remove one battery cable, positive probably best. Remove flywheel/front transmission cover. Remove starter, 2 bolts up, may be support on end opposite flywheel. Remove 2 wires, reverse process to replace. May be 1 or more shims between starter and motor. Keeps starter from grinding on flywheel, may or may not be needed with new starter.
Remove - battery cable Raise and support vehicle if needed Disconnect wiring at top of starter Remove starter mounting bolts Remove starter
Disconnect the - battery terminal Raise and support vehicle if needed Disconnect the wiring harness at the top of the starter Remove starter mounting bolts Remove starter