answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2011-12-13 23:57:39

You should use the one that is recommended from factory and change the size of the ground wires including the one on the fire wall the braided one and get a battery with more cranking amps also should do the trick .

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

Where is the output crank sensor located on a 1995 jeep Cherokee grand Laredo?

in a toilet


Would a oxygen 2 sensor cause a1998 jeep Cherokee not to crank?

No, battery or starter issue or anti theft activated


Where is the crank sensor on a 96 jeep Cherokee?

The crank sensor mounts to the top of the transmission bell housing on a 1996 Jeep Cherokee.


Will a starter crank but not start if the relay switch is bad?

Usually when a starter solenoid/relay switch is bad, you will hear only a click and the starter will not spin (crank).


Why would 98 Cherokee not start turn key everything comes on no crank can jump starter terminals and wil start cleaned neutral safety switch already?

your ignition switch or the starter solenoid is bad try jumping the solenoid instead of the starter, if this does not work, then change solenoid


I get a single click from the starter but it will not crank what is my problem?

your battery is dead or the starter solenoid


Why Gasoline engine will not crank over?

When you say 'crank over' are you saying the engine won't do anything? First check your battery and then your starter or starter solenoid. You can turn the crank to check if the block is seized or not.


If a 92 Jeep Cherokee will crank over but will not start what is the problem?

probably crank sensor, they are famous for that


Do all Honda Civics have a starter?

Or a crank


Why is your starter clicking?

When does it click and does it Crank when it is clicking


Why does your car crank excessively on startup?

the starter


Where is the crank sensor located on a 1999 Saturn SL2 and how do you change it?

The crank sensor is behind the starter. Remover the starter at the back of the engine and you will see the sensor


Where is the crank position sensor in 2000 jeep grand Cherokee with v-8?

It is above the starter. You must remove the started to get at the CPS. There is one bolt that holds the CPS in the block.


Where is crank sensors on 5.3 vortex?

It is behind the starter. You will have to remove the starter to even see it.


Where is crank sensor located on 2000 Chevy Tahoe?

it is behind the starter. You will have to remove the starter to get to it.


How much crank power does a Jeep Cherokee need?

a jeep Cherokee need 220 volts to run


Why doesn't my 1999 Dodge Ram 2500 with a Cummins diesel not crank Have new alternator batteries are fine and I get good voltage to the starter?

If yo have power to both wires at the starter when trying to crank, the starter is failed.


Why does 2002 stratus keep blowing a 20 amp starter fuse?

If it blows every time you try to crank the engine over, the starter may have failed.If it blows every time you try to crank the engine over, the starter may have failed.


Where is crank sensor located on 99 Cherokee xj?

The crank sensor is on the top driver side of the bell housing.


Where is the crankshaft position sensor located on a 5.9liter cummins?

1998.5-2002 it is behind the starter2003 on up, it is on the side of the crank pulley.1998.5-2002 it is behind the starter2003 on up, it is on the side of the crank pulley.


How do you test 1993 grand am starter?

If you can crank the engine over by turning the key: First connect a voltmeter and an ammeter. Then disable the ignition. Note the voltage and amp draw of the starter while cranking. If voltage is too low or amperage too high (check service manual for specifications) it is bad. Otherwise, remove those meters and use an oscilloscope to look for any irregularities in the waveform. If any irregularities exist, the starter is bad. Otherwise, it is probably good. If you cannot crank the engine: Check for BatteryV- at the body of the starter, BatteryV+ at the big wire to the starter and (only while turning key to crank) BatteryV+ at the small wire to the starter. If one or more of these is not present, correct this problem before continuing testing of the starter. Now check that the starter makes some sound (at least a click) while turning key to crank If not, starter solenoid (part of starter) is bad. Otherwise, remove starter from engine but leave electrical connections in place. Turn key to crank. If it doesn't crank, starter is bad, otherwise starter cranks and proceed to testing as if you can crank the engine by turning the key as described above.


If you have power going to the coil and starter but the engine does not turn over where is the problem?

does the motor spin..ie..crank? if no possible locked up engine..try spinning it by hand..correct size socket on front crank bolt turning clockwise.. possible bad starter motor does the starter engage when the key is in the crank possition. if the motor does crank your looking at a fuel or ignition problem


Where is the crank sensor on a 2003 Z66 with 5.3 engine?

It is behind the starter. You will have to remove the starter to even see it.


Where is the crank sensor located on a 2002 Chevy Silverado?

Located behind the starter. Have to take starter off to get to it.


Where is the crank sensor on a 2000 Chevy 3500 6.5l?

It is behind the starter, Will need to remove starter to service it.