We need you to answer this question!
If you know the answer to this question, please register to join our limited beta program and start the conversation right now!
Why do your 1987 Jeep Wrangler crank when you turn on the ignition?
My first guess is that your ignition switch has gone bad, but if you have done work on the engine recently recheck your wiring. ...
Why do your Jeep Wrangler starter engage when you turn on the ignition?
It sounds like your ignition switch has gone bad. If you have done some sort of work on the starter recently recheck your wiring. ...
99 Jeep Cherokee Laredo stay running after turn off the ignition switch?
99 jeep Cherokee Laredo stay running after turn off the ignition switch?
1988 jeep wrangler runs while cranking quits when you let off?
you have an open circut in your ignition switch change your ignition switch. ...
Asked in Auto Parts and Repairs
2002 Jeep Grand Cherokee Engine cranks but is a no start No dash gauges?
A 2002 Jeep Grand Cherokee engine that cranks but is not starting and has no dash gauges is experiencing an electrical system failure. This can be a result of a faulty ignition switch or damaged wiring. ...
Asked in Jeep Liberty
Can you reset the oil light in a Jeep Liberty?
The oil light in a Jeep Liberty can be reset. To reset the light turn the ignition switch on or off without starting the engine. Next depress the acceleration pedal at least three times and then switch the ignition switch in a locked position. ...
Where is the security reset switch on a 2007 Jeep Grand Cherokee?
No such switch. Just put the key in the ignition and turn it on, or unlock with the remote. ...
89 Jeep Cherokee Laredo Ignition key stuck in on position This is the second time last time cost 150 then after the warranty was up got stuck again?
In my case it was the ignition switch itself had overheated and seized up. Replace the switch (have to lower the column, disconnect the wiring plug from the switch, and remove/replace the switch.) Clean all connections to the switch, make sure they're connected solidly and not heating up again. ...
Asked in Jeep Wrangler Sahara, Jeep Wrangler
How do you reset the oil change indicator in a 2007 Jeep Wrangler x?
Switch the ignition ON - then pres the fuel pedal three times - then switch the ignition off .Thats all - miracle is done. ...
How do you remove the door switch wiring harness of a 1993 jeep grand Cherokee?
Depending on type of switch- either unscrew or just pry out
Asked in Jeep Grand Wagoneer
How do you change ignition switch on 1981 jeep wagoneer?
you must remove the steering wheel and turn signal from column. then you can acces the screw to remove the switch. ...
Asked in Power Steering, Jeep Liberty
How do you replace power steering pressure switch for Jeep Liberty 2003?
Remove the wiring harness from the 2003 Jeep Liberty pressure switch. Remove the power steering pressure switch retaining screws. Reverse the process to install the new power steering pressure switch. ...
Asked in Jeep
Problem with turning the ignition in your jeep when starting the car how do you fix it?
Physically has a turning problem ? Try your spare key and still has the problem? Replace the ignition switch. ...
Asked in Jeep Wrangler
Is an ECM and ignition switch the same part difference on a jeep wrangler 1990 2.5?
No! The ECM is the Electronic Control Module (Computer), sometimes called ECU, Electronic Control Unit. The ignition switch is just that, the switch that controls the engine ignition, the power to the starter, starting and shutting the engine off, and power to the accessories. ...
Asked in Jeep Wrangler, Jeep Wrangler Sport
Where is the ignition switch location on 1997 Jeep Wrangler?
first you must tilt the steering wheel to the up position then take the casing off of the bottom of the steering column. the ignition switch will be located right behind the actual key. ...