Crankcases and PCV Valves
Nissan Maxima
Chevy Beretta
Ford Expedition XLT

What is the name for the hose that runs from the pcv valve to the rear vavle cover on a 1995 Chevy berreta?

565758

Top Answer
User Avatar
Wiki User
2005-09-27 03:49:28
2005-09-27 03:49:28

PCV hose. Any quality neoprene hose that has similar dimensions will work.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

on the valve cover as your faceing the car you will see a hose on the left side of the vavle cover. This hose goes to the intake plentum. the hose on the valve cover end goes to a connection that has a 19 mm nut screwed into the valve cover.loosen this nut remove the plastic cover and look in vavle cover. you will see the pcv vavle take a pair of needle nose and pull old pcv vavle out and replace.

User Avatar

on the valve cover (long metal cover on either side of intake. normally on drivers side vavle cover where it says OIL

User Avatar

its located on top of the valve cover. its located on top of the valve cover.

User Avatar

its on the rear of vavle cover,top and in the middle of it

User Avatar

The PCV vavle is located in the rear valve cover just behind the throttle body

User Avatar

The pcv vavle is built in through the valve cover, so not an actual pcv vavle you would see on an average car, if it starts going bad your idle is going to go haywire, an occasional loud squealing, you have to replace the valve cover, which is 136.00. (PCV-Positive Crankcase Venalation

User Avatar

the pcv vaule should be located on the driverside of the vavle cover gasket goin into the air filter housing.

User Avatar

pull the pcv valve out of the vavle cover grommet, pull the hose off of it, put a new one in, put the hose back on, yay!!

User Avatar

The EGR valve is usually located on the top of the valve cover...it is usually a plastic part that connects to the valve cover with a rubber seal...there is an emissions hose leading away from it...the PCV valve is also located on the valve cover in a similar fashion, though it is a lot smaller...

User Avatar

its usually in the drivers side vavle cover. look for a 3/8 rubber hose going to the valve cover. the pcv vavle goes into a rubber grommet and usually comes out at 90 degree angle.

User Avatar

It's where the Aortic Vavle is diseased by narrowing of the Vavle or thickening of the tissue.

User Avatar

top rear of vavle cover under upper intake manifold

User Avatar

vavle cover gaskets. get worn . also there are gromets that go over spark plug illet under valve . ask for valve cover gromets for neon lift valve cover and replace

User Avatar

It uses an orifice in the top rear of the vavle cover not a PCV vavle.

User Avatar

Type your answer here... on this 97 Camry the spark plugs are through the vavle cover and whem i removed the spark plug there are nuts holding the cover down and i didnt see any bolts on the edges of the cover is that the only thing holding the valve cover in place and also is this a hard job thanks Jim

User Avatar

it is in the back of vavle cover on firewall side. you can't see it unless you remove the intake plenum.

User Avatar

pvc vavle should be on the on the vavle cover i think i am not sure sorry On a 5.7 engine it is on the right side of the intake manifold the air intake might have to be removed pcv valve is located on the left side of engine there is a black insulated rubber hose running down the top side of the valve cover squeeze the hose until you find it you may have to slit the hose to change it

User Avatar

It's a valve used primarily for holding air inside of tyres. See you bike tyre vavle.

User Avatar

There is no valve lash. That engine has hydraulic lifters.

User Avatar

to my knowledge ther is no purge valve, but in reference to what .

User Avatar

Top center of valve coverIt has a large hose on it that connects to the intake manifold. To remove it, roll a rag and place it next to the PCV valve, use a pair of pliers to grab the bung and use the rag as a fulcrum to pop the valve out of the grommet. When the valve is removed, remove the grommet from the valve cover and replace both. Its beside the air filter casing and on top of the valve cover on the 88 22R. i used a set of needle nose to get it out and only my fingers for the hose retainer.

User Avatar

Take the cover off and the PCV valve is inside the black plastic thing on the right (passenger) side of the engine. Press down and twist off the cover. Be careful, though, they break easy.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.