torque specs on head gaskets 1988 toyota corolla 4A-F
There are torque specifications for every bolt in a Toyota Corolla 1.3 L engine. The head bolt torque specifications is 70 pounds.
The torque specs for the head bolts on a 1997 Toyota Corolla goes in three simple steps: step one- tighten the bolts in the the correct order to 22lbs step two- in the same order, turn each bolt 90 degrees step three- go through and again in the same order turn each bolt in an additional 90 degree.
The Toyota Corolla 1.6 liter engine cylinder head bolt torque specification is 150 pounds. The head bolts should be torqued in 50 pound intervals.
Look in a Haynes repair manual relative to your vehicle i do not have any manual
Depending on the model/engine type, the cylinder head torque specs for a 1990 Toyota Corolla are: For the 4AFE (1.6) coupe/sedan/wagon: 44 ft lbs For the 4AGE (1.6) GTS coupe: 1st: 22 ft lbs 2nd: additional 90 degrees 3rd: additional 90 degrees
in the 1994 3e-e engine the camshaft bearing cap torque is : 10 Ft-lbf Hope it works for ya!
The brake rotor specs for 93 Toyota corolla the outside diameter 255 mm and inside diameter is 142.2 mm.
There are 2 different torque specs. for different bolts, some are 96in-lbs. others are 18ft-lbs. see link below it has a diagram show which are which.
Toyota Corolla does weights about (depends on a model and specs) 2,822 lbs or 1280 kilos.
4.275m See http://www.cars-directory.net/specs/toyota/corolla/1994_5/2387/
the torque for the cam shaft are 9lbs/foot
The cylinder head bolt torque specs for a 1972-1979 Toyota 2TC 1600 engine is 64-68 ft lbs.
1991 toyota camry head bolts torque specs
98 toyota tacoma head bolt specs
waths the wey to torque the cylinder head
What is the wheel torque on a 2007 toyota tacome truck 4 wheel drive
no timing spec at all due to used timing chain.
The torque specs for a Toyota Camry cylinder head is 60 pounds for the inside bolts and 50 pounds for the site bolts. The cylinder head bolts should be tight from and to end alternating.
petrol/deisel 2.4 or 3.0??
What specs do you need? Torque for the gears or caps? Dimensions? TDC timing marks?
85 N·m (8.5 kg-m, 61lb-ft)
The torque specs and pattern on the head bolts for a 1991 Toyota pickup with a 3.0 EFI is 50 foot pounds per bolt. The pattern is 4,5,6,3,7,2,8,1 with 1 being at the front of the engine.
The 1995 Toyota Tacoma thermostat housing torque specification is 40 pounds. The amount of torque on the thermostat housing bolts is not that important. You basically do not want to break the thermostat housing bolts.
The 1995 Toyota 3.0 liter engine main bearing torque specification is 160 pounds. The rod bearings torque specification is 120 pounds.
The torque specs and pattern on the head bolts of a 1991 Toyota pickup with a 3.0 engine are 5, 4, 6, 3, 2, 7, 1, and 8. This sequence is started from the center of the head and requires 75 foot pounds of torque on each bolt.
My 2007 Matrix R says 77ft/lbs
I had to re- torque mine, and I think they were at 35-38ft/lbs. I went up to 42 ft/lbs and they didn't strip. I still had to replace the gaskets.
i retorqued my Chevrolet heads to 90 ft. lbs. but i also found if you use the specific torque pattern the gaskets will seat better....i don't torque my intake bolts Answer 65 lb.ft.
Torque as follows 53-63 ft/lbs. in 3 steps
the torque specs for the 5.4 is 350ftlbs of torque
torque specs for an 89 chevy suburban
Just tighten them down as tight as you can and then drive the car a few miles and retighten the bolts again as they will be loose after the gaskets heat up.
The best place to go would probably be the Toyota website itself. If you, however, desire a more personal approach you can go to the Toyota dealership and ask one of the salesmen.
Bolt pattern and torque specs are here: http://toyota.offroadforum.cz/aarc.epnet.com/application/8578/8578R03_Cylinder_Head.html
Torque specs for what part of the engine? There is torque specs for everybolt under the hood, some don't need to be used but some are critical
torque specs on 02 5.3
head torque specs for 2002 honda rancher
Call any auto zone or go to their website and look up specs that should tell you
Axle torque specs are as follows: Axle nut torque..............148Ftlbs
Torque Value For 1987 R22, Per Haynes Manual - 58 ft lbs.
n-14 rod and main bearing torque specs
What is the torque specs on a 94 GMA Yukon
Need more info. Torque specs. for what?
what are the torque specs and sequence for a 1992 Nissan maxima manifold
wheel torque specs are 80 foot pounds.
Torque specs for a 1998 Volkswagen jetta 2.0
2010 Harley davidson Street glide rotor torque specs
torque specs for rod and oil pan on 2005 4.0
whats the ring gear torque specs in a 10.25
what is the torque specs and valve lash on a 24 hp Briggs