answersLogoWhite

0


Best Answer

Check the fuse, bulbs/assy., and wiring another thing to check is where the bulbs connect. sometimes like my 94 one of the connectors in the bulb housing was broken. also there is a brake light sensor on the brake petal that is turned on when you depress the brake. usually near the top of the brake petal

User Avatar

Wiki User

โˆ™ 2006-02-08 12:59:33
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: What makes the brake lights on a 99 Dodge Intrepid not work?
Write your answer...
Submit
Related questions

What makes the brake lights work on a 93 dodge colt?

There is a brake light switch or stoplight switch that may be bad on the brake pedal up top.


What operates the brake light switch on 1993 Dodge Dakota?

When your foot puts pressure on the brake pedal there is a switch that relays the brake pedal being pushed to the lights which makes them turn on.


1979 Dodge B200 Sportsman V8 brake pedal makes all signal lights come on with brake lights the hazards or signals don't work on their own could it be a flasher?

On the 1979 B200 Sportsman V8 if the brake pedal makes all signal lights come on and hazards and flashers do not work on their own, it could be the flasher, but the culprit could also be a burned out bulb or a short in the wiring.


What does a brake light switch do?

just as the name it makes the brake lights come on when u press on the brake pedal


What makes a brake light come on when the key is in the ignition?

Is it when the ignition lights on the brake lights are stuck on? If so adjust the brake light switch at the pedal.hope this helps Answer: Its the park lights. The vehicle is probably in park.


Where in the trunk is the controller for the brake lights located in a 1991 Toyota Corolla?

If by 'controller' you mean the switch that makes the brake lights come on, it is not in the trunk. It is located underneath the dashboard, next to the brake pedal.


What would cause brake and tail lights to remain on after the engine is turned off?

There's a switch that the brake pedal engages when pressed that makes the brake lights go on. this switch may be stuck.Or the peddle staying on switch


How do I get the brake lights to work. I have replaced the fuse and that is not the problem.?

Check the switch at the brake pedal, it is what makes the brakes come on, it may be malfunctioning.


Your brakes lights stay on not all the time what do you do.it is a Chevy truck 2002?

Under the brake pedal is a brake light switch that when you press the pedal it hits it and makes your lights come on..sometimes when they get weak the pedal depresses them simply from the weight of the pedal and they stay on..Have a friend get inside the truck and pull UP on the brake pedal as you look at the lights..if the brake lights go off when they pull up on it..then it is that switch under the brake pedal


Cant get the brake lights to work on your 71 el camino turn signals and marker lights ok?

Most Likely the problem with the brake lights would be the switch located in front of the brake pedal arm just below the pivot point. It has a spring inside so that when the pedal is depressed it makes contact internally.


What makes brakes lights stay on 93 Toyota Corolla?

A malfunctioning brake light relay switch will cause your 1993 Toyota Corolla brake lights to stay on all the time. The brake light relay switch is located beneath the drivers side dashboard.


What makes led lights on my truck to flicker or blink when i depress the brake pedal?

Improper resistors.


What makes the brake and blinker lights not work when the head lights are on on your 1993 firebird formula?

Check grounds in light sockets Check for corrosion and loose connections


What makes ABS and brake light come on continuously?

The ABS and brake lights sole purpose is to signal you that you may have a problem with each / or one individual system. From your question we can assume that your ABS and brake lights come on continuously. There by we can safely deduce that you may have a problem with your ABS system and / or your brakes.


Where is the brake light switch on a 1995 Chevrolet Silverado 4wd?

UNDER the dash, on the steering column and it makes contact with the brake pedal It looks like a bracket, that wraps around the brake pedal arm, and it has a cylinder type switch that makes contact with the brake pedal arm. When the brake pedal is pressed down it pushes the cylinder switch together which closes the circuit and makes you brake lights come on. It may be a fuse or wires but start with the switch.


What makes your abs brake light turn on on your 2000 dodge Dakota?

either a bad sensor somewhere, or a connection is disconnected


1998 Dodge Intrepid wont start right away on cold mornings it makes a clicking noise?

Sounds like a starter or battery problem, possibly wiring problem


What turns on the electrical stop light switch in an air brake system?

The switch is attached to the brake pedal itself. An energized pole goes into the switch, and, when it makes contact, the circuit is closed, allowing power to be transmitted to the brake lights.


When my 1998 2.7 v6 Dodge intrepid starts on a cold day it makes a loud noise. We Don't know why. The Mechanic says its normal but my friends Intrepid doesn't do that. Is that normal?

apparently you failed 7th grade english... Please restate this question in proper form to make sense


What makes the tail lights come on when the brake pedal is pressed?

Power is bleeding across the electrical ground from the brake to the tail circuits. Take the rear lights apart. Wirebrush the contacts and where they ground to the body. Put dielectric grease on the contacts when you put the bulbs back in.


Why would the rear running lights stay on after your Honda Civic 2000 is off and it's not the light switch?

What do you mean by running lights?? If it is the brake lights you are talking about, it may be the brake switch. this switch is on the brake pedal and makes the lightrs come on when you press the pedal. if you look to the very top of your brake pedal you should see this switch and a wire connected to it.(You may have to remove some of the trim, you may not. Im not to sure on this year. Hope this helps you some.


How do you switch off daytime running lights on a 2003 cobra mustang?

If you pull the parking brake up the running lights will go off - if not - start the car with the parking brake on and that should work, if you want to drive with the running lights off - you can get away with "slightly" putting the parking brake on (just so the parking brake light goes on in the dash but the brakes itself makes no contact) Otherwise you can remove the relay that controls the daytimes - maybe even a fuse


What makes the parking and dash lights not work on a 1990 GMC Sierra but turn and brake lights do?

They're on a different circuit. The parking and dash lights go through the headlight switch. It could be the switch, a bad wire/connector or a burned fuse.


How do you get tail lights to turn off when the car engine and lights are off?

Look up under your dash where the brake pedal is attached, you will see a switch that makes the brake lights turn on when you step on the pedal and off when you leave off the pedal. The switch is probably stuck. In the meantime you could disconnect the negative battery cable so your battery doesn't die.


Can a bad bulb cause all brake lights in a 98 ford ranger to fail?

It can if it is a dual filament bulb as found on most US. makes. The brake light filament can short over to the tail light filament inside the bulb and when the brakes light is activated, all the tail lights and front marker lights will light also, probably blowing fuses.