This might help if you have a Daewoo Nubira/Lacetti 1.4L/1.6L. What you need is a timing belt adjuster and a angular torque gauge for this operation. First start with the removal procedure; Disconnect the negative battery cable, the air cleaner outlet hose from the throttle body and the breather tube from the camshaft cover. Then remove the air cleaner housing, the right front wheel and the right front wheel well splash shield. Remove the serpentine accessory drive belt and the crankshaft bolts and pulley. Then remove the upper front timing belt cover bolts and the upper front timing belt cover. Continue with the removal of the lower front timing belt cover bolts and the lower front timing belt cover. At this time install the crankshaft pulley bolt and rotate the crankshaft clockwise until the timing mark on the crankshaft gear is aligned with the notch at the bottom of the rear timing belt cover. Slightly loosen the water pump retaining bolts. Using the timing belt adjuster, rotate the water pump counterclockwise to release the tension on the timing belt. Remove the right engine mount bracket and then you can remove the timing belt. Then countinue with the installation procedure; Align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover. Align the timing marks on the camshaft gears. When this is done install the timing belt. Install the right engine mount bracket. Rotate the water pump clockwise using the timing belt adjuster. Rotate the water pump clockwise until the adjust arm pointer of the timing belt automatic tensioner is aligned with the notch in the timing belt automatic tensioner bracket. Tighten the water pump retaining bolts. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt. Loosen the water pump retaining bolts and rotate the water pump until the adjust arm pointer of the timing belt automatic tensioner is aligned with the pointer on the timing belt automatic tensioner bracket. Tighten the water pump retaining bolts and remove the crankshaft pulley bolt. Then install the upper and lower front timing belt covers and their bolts. Tighten the front timing belt cover bolts. Install the crankshaft pulley and the crankshaft pulley bolt. Tighten the crankshaft pulley bolt and retighten 30 degrees plus 15 degrees. Install the serpentine accessory drive belt and the right front wheel well splash shield. Install the right front wheel, air cleaner housing and reconnect the air cleaner outlet hose to the throttle body and the breather tube to the camshaft cover. And finally remember to connect the negative battery cable.
every 60,000 miles
How do you flush the transmission fuel from a 2000 Daewoo Nubira
I have a 2000 Daewoo Nubira and I had the control arm replaced and it fixed the problem.
In 2000 Daewoo Nubira the ECM is located on the front passenger side wall by the front passenger right foot.
behind the alternator
The fuel pump on a 2000 nubira is under the back seat on the passenger side.
on the exhuast header pipes
you cant its all done electronically sorry mate !!
here is the link to the nubira service manual http://chevy.mrmax.dp.ua/EN/GMDE_TIS_START.html
The Daewoo Nubira CDX has 16 valves - it is a 2 litre 16 valve double overhead camshaft 4 cylinder made by GMH in Australia!
yes,it is an interference motor.I just did one and it bent all the intake valves.
it is right underneath the steering wheel gasket
2000 Nubira, same problem, no water flow from block to heater, core not blocked, runs fine????????????
You have to take it to a mechanic i guess since it doesn't have a dipstick.
it could do with the immobiliser, i have to disconnect my battery for 10 mins,then it starts
there is a power button on your shifter for extra power
Under the car hood in the fuze box on the right.
What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and what is the proper torque order
what is the timing marks on the camshaft what is the timing marks on the camshaft
firing order? like for starting the car, the firing of the pistons? redefine the question...
Pull aff ac bracket and the wire will lead you there
2.2L D-tech . Its a 16 valve, dual overhead cam engine, with 130hp.
The heater core is located on the air distributor case. It is covered in the case and directly on top of the assembly.
i Have a nubira II premium M.2000 1.5Ltr and the Map Sensor is located just under the Wind screen wipers inside the engine compartment, to the left of the Coil