0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can you make a ls non vtec into a ls vtec?
Yes you can. You can either use your LS block and put a Vtec head on it or you can just swap it out with a GSR or Type-R motor.
What is a map sensor and where on a 90 Civic with a b18 head and a b20 block?
Manifold absolute pressure sensor, being hondas run of calculations to adjust fuel to air ratio (called speed density) they require this to calculate amount of fuel to use. This is on top of the manifold dependant upon year b18 head, Da's had sensors located on firewall. B20's have the exact same head cast and cams as a b18b head. unless your refering to a vtec head there is no difference.
What engines can you use in place of a D15Z4 without changing wiring ECU etc?
You can use any d15 series motor as long as it is not vtec. But also it isn't to expensive to switch to a d15b vtec motor you just need vtec ecu and wiring harness that can be found for about $100 on eBay. I switched my car from d15 non-vtec to d15b vtec for about $650 including the price of the motor.
What type of fluid does the clutch slave cylinder use in a 1998 Mitsubishi mirage?
The clutch slave cylinder in your 1998 Mitsubishi does not use fluid. The clutch slave cylinder is sealed with grease inside of it.
Can you replace a b18 engine and 5 spd tran with b20 enginetran combination Does b20 come with cable clutch?
you can use the same exact transmission for both engines. they mount up direct and will not cause any problems. the B18 and B20 engines are a direct swap for the most part, just plug and play. but basically if you have the B18B ecu and b18b tranny, intake manifold, distributer and so on.. you can swap everything over
Can you use a vtec ecu on a non-vtec motor?
I'm pretty sure it would be a NO considering vtec engines have camshafts specifically made for high rpm use(when it kicks in). normal cars cams aren't different from low to high rpm. certain Honda's switch camshafts from low cam to high cam when vtec is activated
What are the disadvantages of a centrifugal clutch?
Unless you are using it for something you shouldn't use a centrifugal clutch for, there are no disadvantages. But a clutch of that type can create a lot of waste heat through slipping while it is engaged.
Will Acura Integra rods interchange with D16 rods?
What engine is in the integra? Is it a B18? Is so the aswer is no unfortunately for you. b18 rods will work in a d16 block and crank. the rods of the same length as d series rods but you will have to notch the bottom of the sleave and have to use a bushing to make the b18 ls rod to work on a d series piston. So the answer is yes
What is the best d-series to turbo?
you have many different options when it comes to this, you can go d15b7/d16 vtec head (this is a Frankenstein swap where you put a vtec head on a non vtec block), or d16 vtec, or single or dual cam Zc its personal preference, but do not go for the non vtec motors such as d15s and certain d16s research use wikipedia it works the best to find this information
What type of clutch fluid do you use for a 2002 Mitsubishi eclipse rs?
A person has to use the right type of fluid in a vehicle to help it run its best. The 2002 Mitsubishi eclipse RS uses DOT3 brake fluid as clutch fluid.
What type clutch fluid for 1991 Honda accord?
I would recommend you use nothing but genuine Honda Clutch Fluid. I know it will cost more, but!
What type of fluid for the clutch 85 rx7?
Dot 3 brake fluid is an acceptable fluid to use. It is the standard clutch fluid for most vehicles.
