Best Answer

The clutch slave cylinder in your 1998 Mitsubishi does not use fluid. The clutch slave cylinder is sealed with grease inside of it.

User Avatar

Wiki User

โˆ™ 2014-06-27 21:44:00
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: What type of fluid does the clutch slave cylinder use in a 1998 Mitsubishi mirage?
Write your answer...
Still have questions?
magnify glass
Related questions

Where do you put the clutch fluid on a Mitsubishi shogun?

1. Lift the bonnet 2. Locate the brake fluid cylinder its the big round thing with a white lid on it. 3. Behind this there is a smaller cylinder with a white lid about 2inches diameter. 4. This is the clutch fluid cylinder and this is where you pour the clutch fluid. 5. Don't get fluid on the bodywork or you will damage the paintwork

What kind of fluid is clutch fluid?

You put brake fluid for the clutch master cylinder

What kind of fluid is in 300zx clutch?

There is no fluid in the clutch....The clutch master cylinder takes DOT 3 brake fluid. It is the same fluid that you put into the brake master cylinder

What would make clutch fluid leak from manual Mitsubishi Eclipse GS on the rubber boot of the clutch slave?

The inner seals have failed. You need a new clutch slave cylinder.

Where to add clutch fluid in 1988 F 250?

The fluid for the clutch comes from the brake fluid. After the brake master cylinder, there is a clutch master cylinder which takes fluid from the brakes. Fill up the Brake master cylinder.

Why is clutch fluid reservoire losing fluid in Chevy 1997 s10?

Either the clutch master cylinder or the clutch slave cylinder or the clutch hydraulic lines are leaking.

Where do you add fluid for clutch slave cylinder?

In the master cylinder

Where is 1995 escort clutch fluid located?

The clutch gets its fluid from the master brake cylinder reservoir. The master clutch cylinder sits just below the master brake cylinder reservoir and is fed fluid by gravity.

What if your clutch on your 85 Toyota corolla goes to the floor and is hard to shift?

There are two normal causes. The clutch is worn out or there is a leak in the hydraulic clutch slave or master cylinder. To check the clutch, press the clutch slave cylinder down. If the clutch slave cylinder bellows compresses down to the slave cylinder, the clutch is worn out. Check the clutch master cylinder fluid level. if this is low, then the clutch cylinder need to be checked. To check for a hydraulic leak in the clutch slave cylinder, remove the cylinder's bellows and check for any fluid. If fluid is present, rebuild or replace the cylinder and bleed the system. To check the clutch master cylinder, check the back the of clutch master cylinder for leaks. If fluid is present, replace or rebuild clutch master cylinder and bleed the system. In my experience, hydraulic leaks occur at the clutch slave cylinder.

Where do you put clutch fluid for 96 rodeo?

in the clutch master cylinder

Where is the clutch fluid on a 1983 F100 located?

If it does not have a Hydraulic clutch, then it has no fluid. If it has a Hydraulic clutch the clutch master cylinder is normally located on the firewall, driver's side, near the brake master cylinder.

What is wrong if there is no resistance in the clutch pedal for 1996 Mitsubishi Galant with manual transmission?

it means you have no clutch fluid(brake fluid) or that you possibly have a leak in the line somewhere or that it needs to be bled.might possibly be the master or slave cylinder.first check the clutch fluid resivor.if its empty then you need to top it off and bleed the line @ the master cylinder then at the slave cylinder.then find out why you have no fluid...the clutch fluid resivor is the smaller one of the two,check inside the car for a leak too,follow the clutch pedal to the firewall and you will see the small rod that goes into your clutch master cylinder,if you have a leak there the master cylinder is bad

People also asked