0
When testing amperage in excess of 10 Amps what meter connections should be used?
Wiki User
∙ 8y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What makes a marine battery's terminals hot?
Amperage draw, excessive amperage draw, and or dirty & loose connections. This should be checked out if the temperature is elevated when not cranking your engine.
What should I check if my 94 Sonoma is completely dead?
Start with checking/testing condition of battery and battery connections.
What size fuse should be used for 2 amp power supply?
If the 2 amps is the output amperage of the power supply, the maximum that should be drawn from the unit is 2 amps. The load amperage that is connected to the power supply should govern the amperage of the fuse used. There is not much range there, the fusing could go from .25 to 2 amps. If the input amperage is 2 amps then the input and output voltage of the power supply should be stated.
How much would a truck battery cost?
The battery for your truck should cost approximately $150. With installation, charging system testing fee, and taxes you might be paying in excess of $200.00.
What amp wire should you use for 3000w lights?
Wire size is based on the amperage drawn. To find the amperage, the voltage must be stated. Use this formula to find the amperage. I = W/E. Amps = Watts/ Volts. Once you have the amperage, restate your question using the new found amperage or state the voltage that supplies the lights.
If my AC technician says my unit is rated at 28.9 amps and drawing 24.8 and should draw about half of rated capacity and that compressor needs to be replaced Is this correct?
There are several amperage ratings on AC compressors/motors. Locked Motor Amperage (LRA) is the amperage that the motor is fused for. The load of the motor is expressed in amperage or wattage, which is probably the case here. Low amperage readings on an AC unit being charged by amperage load would indicate low freon. High amperage readings indicate overcharge when charging by the amperage load. AC units are not accurately charged by amperage readings and the efficiency of motors is not expressed in amperage readings.
What amperage extension cord should be used for microwave?
15A should be the max needed for household versions
Why should you eat excess of food?
The only time you should excess of food is if you are underweight and you need to gain weight.
What are the principles of software testing?
Software testing is an execution of a program with the intention of finding bugs.Please visit www.istqbsoftwaretesting.blogspot.comHere you will software testing tutorials and istqb software testing study materialThe following can be described as testing principals:All tests should be traceable to customer requirements.Tests should be planned long before testing begins.The Pareto principal applies to testing.Testing should begin "in small" and progress toward testing "in large".Exhaustive testing is not possible.To be most effective, an independent third party should conduct testing.
How do you tell if the starter is bad on 1981 El Camino?
Take the car to a repair shop and have them do an electrical systems test. It should include testing the starter for the amount of current dtraw it has. Also the alternator for amperage and voltage output and the state of the alternator. If the battery is low then you will get a bad starter reading.
Can you run a motor of greater amperage draw with a motor of less amperage draw?
It looks like you are asking if a higher amperage motor can replace a lower amperage motor. It depends on what the amperage difference is. If the amperage is high enough to move the capacity of the wire out of its rated value then it should not be done.Remember motor conductors have to be rated at 125% of the motors nameplate amperage. As the amperage increases so does the HP and the motor's protection will also have to be increased or the motor will trip the lower overload protection settings.Also keep in mind that if the motor is three phase, running a motor with higher HP on a load that does not need the extra HP, it will lower the power factor of the supply distribution.
How many amps does a device need?
Look on the devices nameplate. There it should have the wattage, volts, and amperage.
