0
When you press the brake pedal in your olds silhouette the turn signals in instrument cluster light up any ideas?
Wiki User
∙ 13y ago
It could be thast your turn signal flasher module is going out
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
When you turn your headlights on the instrument cluster does not come on and the brake lights and the brake running light do not come on?
You have blown a fuse, look for an acc. fuse out.
Where is the fuse for the instrument cluster located for infiniti j30?
next to the parking brake pedal on the driver side
Why are the headlights working but no turn signals no instrument panel and no brake lights?
Check the fuses and the bulbs.
What fuse box controls instrument cluster on 97 jeep wrangler?
The fuse box just above your emergency brake pedal.
What does the light with an exclamation point within a circle mean on my 99 mercury cougar?
There are two of them, which one? Instrument cluster - parking brake on or low brake fluid Overhead console - brake pads need to be replaced.
What is the green light in the Isuzu NPR?
The green light in the instrument cluster means that the exhaust brake is on, which is a good thing if you drive mainly in the city. the exhaust brake allows you to elongate the life of your brake shoes or pad by using engine exhaust as a brake.
How hard is it to replace instrument panel lights on 1995 Nissan Quest?
# Disconnect the negative battery cable. # Apply the parking brake and block the rear wheels. # Turn the ignition switch to the OFF position. # Shift the gearshift lever to the 1position. # Position the steering wheel in the full-down position. # Remove the two instrument cluster bezel screws. # Separate the instrument cluster bezel from the instrument panel enough to gain access to the electrical connectors. Disconnect the following electrical connectors: # Rear window wiper/washer switch # Rear window defogger switch # Hazard warning flasher switch # Power E-AT switch, if equipped # Security indicator lamp, if equipped # Cruise control ON/OFF switch # Headlamp switch # Remove the instrument cluster bezel with the switches attached. # Remove the four instrument cluster screws and separate the instrument cluster from the instrument panel. # Position the cluster to gain access to the gearshift indicator. Remove the gearshift indicator from the cluster. # Disconnect the electrical connectors from the instrument cluster and remove the cluster. # The installation is the reverse of removal.
How do you remove the instrument cluster on a 2003 Ford Crown Victoria?
Removal and Installation Remove the instrument cluster finish panel. Remove the lower steering column cover. Remove the lower steering column cover retaining bolts. Position the parking brake release aside and remove the lower steering column cover. Remove the retaining bolts and remove the lower steering column reinforcement. Position the transmission range indicator cable out of the way. Disconnect the cable.Remove the retaining screw and position the cable aside. Remove the instrument cluster screws and position the instrument cluster aside. Disconnect the electrical connecters and remove the instrument cluster. To install, reverse the removal procedure.
How do you remove instrument cluster from 1999 Chevrolet 1500 pick up?
Engine Off. Park brake engaged. Put Gear shifter into 1st. Pull off the cluster trim. remove the four 9/32 head screws holding in the cluster. Carefully pull the cluster out enough to unplug the electrical connector.
Where is the rear brake switch for a 1992 Chevy G20 Conversion Van?
hi there should be same as mine which is located behind the dash you can either access it from below the dash which is awkard or remove the instrument cluster panel and unbolt the heater controls and instrument cluster as the switch is located behind them hope this is of use to you nate
Where is the brake fluid reservoir in 87 vw vanagon?
Pretty sure it is in the dash. If you push forward on the instrument cluster housing it will come off and you will see the reservoir on the left.
How do you get to the speedometer cable of a 1990 Toyota 4x4 pickup truck?
There are two types of speed sensors and you can't tell until you look. One is electrical/magnetic (VSS) and one is a cable that goes directly into the instrument cluster. Here is my answer to How to replace the Speedometer Cable in a 1990 Toyota 4x4 Pickup 3.0 3VZE V6. To remove the cable you will need to unhook the e-brake assembly and seperate the speedometer cable from the e-brake at the firewall by the gas pedal. On end goes to rear of the instrument cluster and the other end attaches to a small gear at the rear of the transmission. The instrument cluster will need to be removed.
