Auto Parts and Repairs
Serpentine Belts
Ford Expedition XLT
Ford F-150

Where can you find the schematic for replacing a serpentine drive belt on a 1998 Ford Windstar 3.8 engine?


Top Answer
User Avatar
Wiki User
2011-10-18 21:07:03
2011-10-18 21:07:03

Yous should find this under the hood on top of the radiator cover. If not, you try the click on the repair info, then on the vehicle repair info. The letters A, B, C etc. will be on the screen. Select the letter which is the beginning of the letter of the part that you want to work on and it should take you to the step by step section.


Related Questions

Windstars were offered with a couple of different engines - each engine requiring a different serpentine belt. See "Related Questions" below for more

The diagram for replacing a serpentine belt for the 1991 Jeep Cherokee Laredo is located on the front of the vehicle inside the engine compartment. You can also find this diagram in the Chilton's manual for this vehicle.

Where can I find a engine schematic on line, for a 1999 Oldsmobile Intrigue 3.5 V6.

Put Auto zone in your search engine and they should have the repair guide or the diagram for the belt.....

this is a 150 engine for a verucci motorcycle. where can I find a schematic?

There should be a schematic on the fan shroud for the serpentine belt I don't know about a '98 Riviera but I have a 1996 Riviera & it's in my original owners manual. Athough I do not have a engine belt diagram on the fan shroud, I do have a decal for the enviormental control system. ANSWER: There is a schematic in the owner's manual of the '98 Riviera.

Windstar 3.8 serpentine belt is tensioned by a belt tensioner. This is a pulley about 4" in diameter toward the back of the engine with a built in spring that pivots the pulley toward the back of the engine keeping the belt tight. there is no adjustment. Put a long rod into the gap just to the right of the pulley and rotate the pulley upwards by pushing down. You will be pushing against the spring. This also allows removal of the belt.

Do you have a 3.8 engine for a 2001 Windstar Ford Van?

replacing achieva serpentine on a 96i have a 96 and you have to completely remove the motor mount and all of the bolts holding it on the engine to replace the belt,also carefully jack up the engine since it will fall on the ground if you take off the mount

There is no carburetor on a 2001 Ford Windstar engine because the engine is fuel injected

Yes, there is an engine wiring schematic for a 1981 Volvo 242 DL. You can find this schematic online at places like Volvo Tips and E Euro Parts.

I have a 95 GC Laredo and the serpentine belt routing diagram is "printed" on the top of the belt tensioner mechanism which is on the LEFT side of he engine compartment as you are facing the front of the vehicle.

3.4 ltr v-6 its on the front lower left hand side of the engine where the serpentine belt runs

It is NOT the same as a 4cyl. I had to remove the air filter box and the right-side engine mount in order to replace this belt

Put the serpentine belt on to the pulleys of your 1994 Chevy engine. Tighten a serpentine belt with the tensioner pulley.

when replacing the oil pump on a 98 ford winstar 3.0 liter engine do I have to pack the gears on the new oil pump

There really isn't a multiple choice for what type of belt is on a typical engine.The people at the auto parts store will look it up and tell what the brand choices are.IMHO, buy something up the quality scale from the bottom. The serpentine belt is too darned important to skimp on.See "Related Questions" below for more about Windstar serpentine belts

what engine size? 2.0 soc does not have serpentine belts,has 2 serpentine timng belts. need engine size to help more.

In a 1998 Ford Windstar : There were 2 engine sizes offered from the factory : A 3.0 liter V6 engine and the 3.8 liter V6 engine

after replacing points in engine, can correct timing be done to engine if engine is not run.

The schematic for an 83 Chevy 305 engine can be found in the service manual. It gives the location of each component and how everything is connected.

A wiring schematic for a ford 38 engine can be found through Ford related service manuals. The manuals depict the original factory placements of the harness and parts of the engine.

Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.