0
Where does the hose connects that runs from the oil filler cap of a carbureted 5.0 mustang?
Wiki User
∙ 14y ago
I'm assuming here, as I am not entirely familiar with a 5. Mustang.
Generally, in carburettor models, the hose attaches to carburettor itse'f. It is normally a hose that recycles gases that are in the engine back into the carburettor as what i stermed as crankcase ventilation. So check on the carb, generally after the air filter but before the carb intake. So it could be connected to the air filter housing somewhere.
Mostly, the purpose of thes pipes is to:
1. Ensure that gases, that have escaped past the piston rings, don't build up excessive pressure, (as they could hinder the motors function).
2. Better fuel economy by cycling back unburnt gases into the air/fuel mixture.
3. By cycling back gases, some oil is mixed in and fed into the carb and into combustion chamber. This then slightly lubricates the upper cylinder area.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where is the thermostat located on a 1993 mustang 5.0?
follow the top radiator hose to where it connects to the engine the top radiator hose connects to the thermostat housing , the thermostat is inside the thermostat housing
Where is the MAF sensor on a 2002 Ford Mustang 3.8L?
The MAF is attached to the intake hose where it connects to the air box.
Fuel filler tube 97 neon?
The fuel neck? its about 150 dollars brand new. or it could be the rubber hose that connects it to the fuel tank. which would be only a few dollars.
Where does the hose go that connects the nozzies on your washer system in your 66 mustang?
It goes to a bag hanging on the fender wall that holds the washer fluid.
How do you replace a Fuel Filler Hose on a Subaru Outback?
how to inspect fuel filler hose on 2004 subaru outback
How do you replace fuel filler neck on dodge stratus?
This is a job that just about anyone can do. 1) block front tires and Jack up Left rear side of car. 2) Remove Rear Tire. 3) pull plastic cover that protects the filler neck. 4) undo hose clamps on the filler neck side of the robber hose that connects the tank and fuel filler neck on your stratus. 5) undo the 3 bolts at the top of the fuel filler pipe. 6) pull the filler neck our of the hose and put your new stratus, cirrus or breeze fuel tank filler neck back in place the same way taken apart.
How do you disconnect the fuel filler hose from the fuel tank of a 1999 Suburban so you can change the fuel pump you don't know how to reach the clamp where the hose connects to the fuel tank?
On some models you can unscrew the bolts that hold the neck at the top where it connects to the body of the vehicle and drop the neck with the tank.Check yours and see if you can.
What is the rubber hose that connects from the chasis to the rear axle for?
The rubber hose that connects from the chasis to rear axle is for grip.
Where is the thermostat located on a 2001 Ford Mustang v6?
If you follow the top radiator hose from the radiator , it connects to a housing that is bolted to the front of the engine . The engine cooling thermostat is INSIDE the housing on your 2001 Ford Mustang , 3.8 liter V6 engine
Where is the thermostat on a Camaro?
Follow the upper radiator hose to where it connects with the intake manifold, (motor) in the housing the hose connects to, is the thermostat.
What is the part called that connects the radiator hose to the radiator?
a hose clamp
Where is the thermostat located on 96 ford mustang 3.8 l v 6?
The thermostat is inside the intake manifold. The upper radiator hose connects to the thermostat housing (on the engine side,not the radiator). Remove the hose, then remove the two bolts holding the housing and there is your thermostat.
