Car Computers and Sensors
Acura Integra
Acura Legend

Where is the IAT sensor plug in a 2000 Acura Integra LS?

969798

Top Answer
User Avatar
Wiki User
2015-07-17 17:56:39
2015-07-17 17:56:39

Driver side if intake manifold last cyl. up on top

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The 2000 Acura Integra OBD 2 port is under passenger dash

User Avatar

From the Haynes Acura Integra Repair Manual, 156 in-lbs.

User Avatar

The plug is under the dash on the passenger side. It should be a green plug just under the carpet..

User Avatar

It is on the exhaust manifold. If you look down at your exhaust manifold there should be one plug sticking out of it. That's the O2 sensor.

User Avatar

follow the lower rad hose from the rad to the engine. its in the houseing right before the hose meets the engine block. will be an electicle plug in (some sort of sensor) and also a c clam will be present.

User Avatar

The thermostat on a 95 acura integra ls is located on the left back side of the engine. below the intake. You will see a sensor plug-ed into it. The thermostat has 2 ten mill bolts holding it together and they are a pain. The best tool for the job is a ratchet wrench.

User Avatar

1-3-4-2 in a clockwise rotation... = 1993 Acura Integra 1.8 liter DOHC L4 =

User Avatar

The drain plug is on the drivers side of the radiator. It is almost straight down from the headlight assembly.

User Avatar

2000 Acura TL 3.2L MFI SOHC 6cylThe Spark Plug Gap.044 (In thousandths of an inch)

User Avatar

It should be a white (or road stained black) plastic plug on the bottom left or bottom right of the radiator.

User Avatar

The 2000 Acura TL OBD 2 port is above shifter

User Avatar

On the exaughst manifold, it looks sort of like a spark plug. You need a special socket to remove/install it. DO NOT CUT ANY WIRES. Buy the OEM or better O2 sensor. The $20 universal ones will not last but about 6 months.

User Avatar

yes its the same exact motor.. B18B(enter USDM number here) its mostly plug and play... seeing that its comming from a OBD2B car to a OBD1 car... you will need to change injectors, distributor, and alternator... unless you have the engine wire harness out of the 97 then it will be plug and play.

User Avatar

1995 Acura Integra probably doesn't have a distributor, it would have coil packs, follow your spark plug wires from the spark plugs back. where the spark plug wires stop that's what has taken the place of your distributor. Its computer controlled the computer is probably under the dash on the passenger side of the car

User Avatar

On the passenger side of the center console behind the head unit for the stereo.

User Avatar

The 1997 Acura intake air temperature sensor is located on the air filter housing. The sensor will be on the right hand side of the air filter housing.

User Avatar

Unplug all the spark plug wires. then loosen the screws holding the distributor on, remove it, put the new one on and screw it in, then replace the spark plug wires

User Avatar

Bottom corner of rad, inner side, some aftermarket rads won't have a drain and you will have to pull the lower hose off to drain it

User Avatar

the iat sensor is located on the tube running from the air cleaner the sensor has a wire connector running to it

User Avatar

if its a manual transmission you dont have one it has a plug you unscrew and look into if its an automatic its on the passenger side(the side with the transmission) it will have a yellow handle on it.

User Avatar

The" manual" trans axle check/fill plug is located on the passenger side of the trans axle. use a box end wrench to remove it.

User Avatar

The correct plug gap for the 94-01 Integra GS-R is .052 inch. As a little added bit of info, the correct plug is a NGK PFR6G-13.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.