Crankcases and PCV Valves
Mitsubishi Mirage
Toyota SR5

Where is the PCV valve on a 1995 Mitsubishi Mirage?

525354

Top Answer
User Avatar
Wiki User
2009-04-21 01:08:54
2009-04-21 01:08:54

Under the hood, on the Head Gasket cover (Where you put in the oil) the top right corner. You'll see a black hose feeding into a silver bolt connected to the Head Gasket. Turn off the car, let it cool, pull the hose off and unscrew the bolt (the entire thing is the PCV). It'll take you all of 3 minutes to change it! MoreDefinately make sure the engine is cold. The PVC valve screws into aluminum which is easy to strip out.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Right next to where you put in the oil (Gasket Cover)

User Avatar

You can find the PCV valve for your 1997 Mitsubishi Montero on top of the engine. The PCV valve will be in front of the air cleaner housing.

User Avatar

Locate pcv valve on 1995 ford contour

User Avatar

where is the pcv valve located on a 1995 Isuzu rodeo v6 3.2l

User Avatar

where is the pcv valve locate on 95 Honda passport

User Avatar

The PCV valve on a 1995 Buick Park Avenue is located on the top of the valve cover. Twist the valve and pull to remove and replace it.

User Avatar

The 1995 Ford Ranger 3.0 liter engine PCV valve can be found on the top of the engine. The PCV valve will be on the back side of the air cleaner.

User Avatar

pcv is located on the engine valve cover will have a black rubber hose attached to it

User Avatar

On my 1995 the PCV valve is on the engine valve cover , on the driver side , near the rear of the valve cover

User Avatar

Remove the vacuum hose from your 1995 Lincoln Town Car PCV valve. Remove the retaining screws from the valve. Reverse the process to install the new PCV valve.

User Avatar

Back left corner of valve cover on 2.0L engines. it is screwed in.

User Avatar

The PCV valve on the 1995 Jeep Grand Cherokee Laredo V6 engine is on the oil filler tube. It is on the top of the engine.

User Avatar

right front valve cover open the hood and on the drivers side valve cover in the front you will see it

User Avatar

PCV valve should be on bottom right side of motor. to the right of the last spark plug. Pull it out with car off. It comes out with a hose on it. Insert new PCV valve into hose. Insert PCV into open hole.

User Avatar

It is stuck in a rubber hose and pushed in the top of the valve cover

User Avatar

Pull upward on the hose that the PCV valve is in. The PCV valve will pull out of the hose. The PCV valve is located in the valve cover.

User Avatar

on my 96 2.4 its right on the valve cover,has a hose going to the intake manifold

User Avatar

The PCV just slips out and slips in; no tools required in most cases.

User Avatar

Disconnect the PCV valve tube from the PCV valve.Disconnect the PCV valve electrical connector if it has one.Turn the PCV valve counterclockwise to remove from the valve cover.To install, reverse the removal procedure.

User Avatar

OK! Look at your oil cap(where you add oil, for the engine)on the valve cover. To the left, or right of the cap, you'll see a black rubber hose(hose is about the diameter of a AA flashlight battery) that goes into the valve cover. PCV valve is on one end , or the other. Some pull out, some you'll need a crescent wrench.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.