answersLogoWhite

0


Best Answer
Copy

well hi. the best i know of the pcv valve for the Ford zx2 zetec 2.0 dohc engine, is that it is located at the front right part of the engine as you are looking at the engine. it's located half way down the right side next to the head. look for a small curved rubber hose with a radiator hose above it. you will need small hands or long fingers to be able to pull the pcv valve out of the seal from the side of the head. T.C. Wichita,Ks the pcv valve on the ford zx2 zetec dohc 2.0 engine is located at the front right as you're looking at the engine. it's in about the middle, with a small curved rubber hose from the head. you have to have small hands and fingers to be able to reach in their and pull the pcv valve out of the seal due to a radiator hose closely above it. Yes, that PCV Valve is right down where the other two had said, and not only long fingers, but some patience will go a long way. Many thanks for the help. Looked like previous owner didn't go the distance replacing the PCV valve, but all is good now ! Onward to the Fuel Filter !!!

User Avatar

Wiki User

โˆ™ 2005-05-07 20:20:48
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: Where is the PVC located on a ford escort zx2002?
Write your answer...
Submit

Related Questions

Cost of ford 1998 escort PVC value?

PVC Valve: Probably just a couple dollars...they're pretty cheap


Where is the PVC valve on a 1993 Ford Escort?

There are 2 locations- for the 1.8L, the pcv valve is located on the valave cover; on 1.9L and 2.0L engines, the pcv valve is located on the crankcase vent, which is located on the left-hand of the ignition coil module.


Where is the PVC valve located on a 1997 Ford Contour?

Its Located be hide the Exhaust manifold, You have to take off the Cat, to get to it


Where is the PCV valve located on a 1990 Ford Ranger 4-cylinder engine?

where is the PVC valve located on a 1990 ford ranger 2.3 L


How do you replace hoses that connect to Pvc valve on a 1999 ford escort?

stick your meat puppet in it,spray ether up your gaping hemmoroids, then light your farts


Where is your pcv valve located on a ford focus se dohc?

where is the pvc valve on a 2002 ford focus dual overhead cam ztec 2.0


Where is the PVC valve on a 1995 ford Eddie Bauer Expedition?

.cv valves are located on top of your engines valve cover.


Where is the PVC value located at on a 1992 Chevrolet Corvette?

Its not A PVC Its A PCV Value Its not A PVC Its A PCV Value


Where is PVC on 2008 Taurus?

Where is PVC valve located on 2008 Taurus


Where is the PVC located on the 1997 ford ranger 2.3 Liter engine?

the PCV is mounted in the oil separator on the left side of the engine


Where is the PVC valve located on a 2002 ford ranger XLT 6 cylinder 4.0 liter engine?

where is the valve located on the 2002 ranger 4.0 liter 6 cyl?


Where is PVC located on 98 eclipse?

The PVC valve on a 98 Eclipse is located on to or the valve cover. It is connected to the intake with a hose.


Where is the PCV valve located on a 1997 Ford Escort LX?

La Valvula PVC se encuentra dentro de la caja del filtro de aire It depends on what engine you have -1.8 or 1.9. On the 1.8, the pcv valve is on the valve cover; on the 1.9, the pcv valve is on the crankcase vent tube.


Where is PVC located on 2001 maxima?

The PVC valve on a 2001 Maxima is located in the rear valve cover just behind the throttle body.


In your 2001 Ford Escort the check engine light came on P 171 and fuel filter was changed as well a vacuum leak was fixed and a tuneup done but for the third time light and code came on what to do?

Changed the pcv valve. It fixed my p171 code on my 2001 escort. Have to get the PVC valve from the ford place. They are the only one that carry the right one. PCV valve is available at AutoZone part # PCV 1001 for 2001 Escort SOHC 2.0L


What does the PVC valve look like on a 1999 ford escort zx2?

This is a very small piece. It costs no more that 5 bucks at any oil change place to have it replaced. I did my own. There was actually a diagram on the inside of the hood that pointed it out.


Locate pcv valve on a 2000 ford expedition?

PVC Valve is located valve cover / crankcase cover. Removal; 1. Disconnect the oil separator hose from the PVC valve. 2. Remove the PVC valve from the grommet in the crankcase. 3. inspect the grommet for deterioration. To Install; 4. If necessary, replace the crankcase grommet. 5. Install the PVC valve. 6. Install the hose.


What brands of lawn chairs are non-PVC?

There are lawn chairs that are non-PVC which are located in various Pier one locations throughout the Untied States.


Where is the PVC valve on a 3.8 engine?

where is the pvc valve located on a 1980 olds cutlass 3.8 v-6


Where is the PVC in a Nissan fronter 2002?

where is the PVC fitting located at on the 2002 Nissan fronter with a supercharged 3.1 motor


Where is PVC valve located on 2003 Chevrolet Impala LS 3.8?

where is the PVC valve on chevelet impala 2003


Where is the Location of PVC valve on 1989 Ford Escort lx?

It doesn't have one. PCV functions are done by several vacuum hoses and a couple of plastic doohickies that I have never really known what to call them. Go to the Ford parts dept. Grab the oldest looking parts person there, and tell them that you need the plastic PCV pieces for an 89 Escort that look like little space ships, and some vacuum hoses to fit.


Where is the location of the PVC valve on a Pontiac Vibe?

Pontiac PVC Valve is located on the Driver's side rear valve cover.


Where is PVC val e located on ford bronco II?

You PVC valve is gonna be on the right hand side valve cover it will be a lil rubber grommet that has a small hose coming out of it remove the hose from the grommet and with a pair of needle nose pliers and some lubrication gently pull the grommet our and the PVC valve should be inside of the rubber grommet


How do you change PVC valve on 2003 Ford Taurus?

The PVC on a 2003 Ford Taurus 6cyl. Duratec engine. I made a tool out of a 3/4 inch PVC plastic pipe i got from Home Depot. I took the new PVC car part and matched it up with the end of the square plastic part by filing out the corners of the pipe and fitting it over the end of the sguare part of the PVC car part. I did this to be able to reach the old PVC so it could be turned 1/2 to the left to get the old PVC car part out.