The brake light fuse on a 1995 Acura Integra is located inside the cabin of the vehicle. It is on the same circuit as the dash and hazard lights.
The brake lights are located in the trunk of a 1997 Acura Integra. To replace them open the trunk and find the plastic housing. Remove and replace the bulbs.
The 1991 Acura Integra brake lamp number is 2057. See sources and related links below for a picture and more information.
On a 1989 Acura Integra hatch back the brake lights are reached through the hatch itself. The brake lights housing are on the rear of the vehicle. Unplug the bulbs and replace them.
my 95 integra has a problem with the brake light located on the hatchback. I haven'y figured out what is causing it , but I have located it and it appears that something is loose inside that brake. Should figure it out here soon.
brake lights won't go off 1995 acura intergra
cut the wire
There is a sensor in the top of the brake cylinder where you put in the fluid. Replace it and the light will go away.
i am pretty sure there are no daytime running lamps on a 90' integra...
they dont have day times....
The parking lights on a two-door 1990 Acura Integra hatchback are located in between the headlights and the blinker lights. Replacement requires a size 3652 parking light bulb.
the fuse is under the hood, in a fuse box located on the passenger side, open and ull see the diagram, its also the same fuse for the horn and cruise control as well, good luck!
The brake light failure sensor on a 1997 Acura 2.2 cl is located on the rear of the car. It is on the back of the left rear lamp assembly.
When there is erosion in the break light assembly it will do this. The wiring to the break lights may also be grounded out.
The Integra uses a dual-filament bulb in the tail light, which has one contact for the running light (the lights you turn on at night) and another brighter one for the brake light (only goes on when you press the brake pedal). You have replaced the bulb with the wrong type. You will need a 2057 bulb for the Integra.
Under the dash. Mounted to the firewall. There's a red flashing light on the bottom side of it.
you may have air in the brake line. bleed all the brakes. if the light still comes on intermittently go next to bleeding the line at the master cylinder.
The easiest way to reset the check engine light on a 1995 Acura Integra is to unhook the battery for a few minutes. If the light is still on after hooking it up again, there is probably still a problem that needs to be fixed with the engine.
check the bulbs
Usually controlled by a fuse and a switch located at the upper end of the brake pedal under dash
If an Acura Vigor brake light is not working there are likely two reasons. One is that a fuse is blown and the other is that the bulb is blown. It could be both.
1998 Acura Integra center high mount stop (third 3rd brake light) light bulb lamp replacement: Purchase the correct replacement center high mount stop (third 3rd brake light) bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the center high mount stop (third 3rd brake light) bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. If there are multiple bulbs, you may want to consider replacing all at the same time in order to keep brightness and color equal (optional).
it may need a new bulb
On the break pedal assembly, it's kind of hard to get there but it's a little black button. When it's pushed in, the lights turn off and when it's depressed, the lights turn on.
You will need to change the brake light switch. The brake light switch can be found below the dashboard on the drivers side.
you might have a short some where, you could start looking in the fuse panels. Also check the connection of the brake sensor, is the one that make the lights turn on.