Car Computers and Sensors
Buick Regal
Crankshaft Sensors

Where is the camshaft position sensor on a 1991 Buick regal?

303132

Top Answer
User Avatar
Wiki User
2005-11-06 20:21:56
2005-11-06 20:21:56

On the 3.1L & 3.8L engines, the CMP sensor is located on the timing cover, behind the water pump, near the camshaft sprocket.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The camshaft position sensor on a 1992 Buick Regal looks like the end of a ratchet.

User Avatar

how to remove crankshaft position sensor from 91 Buick Regal

User Avatar

The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.

User Avatar

Under hood, passenger side, lower engine area, below water pump, mounted on timing cover.

User Avatar

Where is the knock sensor located on a 1992 buick regal

User Avatar

Where is the map sensor on a 2001 Buick Regal Ls

User Avatar

Where is the headlight sensor for a 1999 buick regal? Its in the back, sike ;D

User Avatar

The 2000 Buick Regal 3.8L Crankshaft Position Sensor is located behind the harmonic balancer pulley.

User Avatar

Coolant Recovery Reservoir. There is no sensor in the coolant recovery tank on a 1998 Buick Regal.

User Avatar

On a 1993 buick regal it is on the passager side of the radiator. Hope this helps

User Avatar

On a 1994 Buick Regal 3.8L engine, the camshaft position sensor (CMP sensor) is located on the timing cover, behind the water pump, near the camshaft sprocket. Basic removal and installation instructions: # Disconnect the negative battery cable. # Remove the serpentine drive belt. # Remove the power steering pump, as outlined in Section 8 of this manual. # Detach the sensor electrical connector. # Remove the CMP sensor mounting bolt, then remove the sensor from the engine. # Inspect the sensor O-ring seal and replace as required. To install: # Position the CMP sensor and secure with the retaining bolt. Tighten the bolt to 8 ft. lbs. (10 Nm). # Attach the sensor electrical connector. # Install the power steering pump, as outlined in Section 8 of this manual. # Install the serpentine drive belt. # Connect the negative battery cable.

User Avatar

The cam sensor on a 99 Buick Regal is located behind the rear cam bearing cap. It monitors the rotation of the cam and relays information to the vehicle's computer.

User Avatar

On a 1993 Buick Regal 3.1L, the PCV valve is located on the intake manifold. It is situated underneath the MAP sensor.

User Avatar

Buick Regal was created in 1973.

User Avatar

could be the crank sensor, the go out. the have a reputation for that.

User Avatar

which fuze controls the air in a buick regal

User Avatar

P0410 2002 buick regal

User Avatar

In order to replace the cam sensor on a Buick Regal 3.8L, you must first access the main dash board from the back by either entering the hood or removing the panel, and then crossing the two wires in question.

User Avatar

under the cover, right side. there some letter on the sensor <ab?>

User Avatar

where is the thermostat located on 95 buick regal


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.