answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2007-09-09 00:45:20

It's on the front of the engine below the water pump

Rick

I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technology. Visit my blog for cool articles and TSB's: http://free-auto-repair-advice.blogspot.com

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

Where is location of camshaft position sensor on 1991 buick lesabre?

under the water pump.


What does the camshaft position sensor on a 1992 Buick Regal look like?

The camshaft position sensor on a 1992 Buick Regal looks like the end of a ratchet.


How do you replace your Camshaft Position Sensor Interrupter Magnet in your 1994 buick lesabre?

The interrupter magnet is normally replaced by removing the camshaft gear as the magnet is inserted through the back side of the gear.


What is the fault code P0336 on a 1997 Buick lesabre?

The P0336 fault code on 1997 Buick Lesabre is a fault in the crankshaft position sensor circuit.


Where is the camshaft sensor on a 1989 Buick LeSabre?

it should be behind the water pump pulley on the lower left side when looking at it from the side of the car.


Where is the camshaft position sensor on a 1991 Buick regal?

On the 3.1L & 3.8L engines, the CMP sensor is located on the timing cover, behind the water pump, near the camshaft sprocket.


Where is the Crankshaft sensor on a 2000 lesabre?

The 2000 Buick Regal 3.8L Crankshaft Position Sensor is located behind the harmonic balancer pulley.


What causes the engine to idle so fast on a 1995 Buick Lesabre 3.8?

throttle position sensor believe it or not!


Where is the 97 Buick LeSabre 3.8 V6 Coolant temperature Sensor?

where is coolant sensor on a 97 buick lasbre


Where is crankshaft position sensor on 97 buick lesabre 3.8?

The Crankshaft Position Sensor is behind the crankshaft pulley (harmonic balancer). You will need a ½-inch drive breaker bar and appropriate socket.


What does the camshaft interrupter on a 1989 Buick Lesabre do and where is it located?

It should be behind the camshaft postition Sensor in the timing box attached to the end of the CamShaft. It allows the computer to know where the cam shaft is in order to properly inject fuel to the proper valve at the proper time.


Where is the camshaft position sensor located on a 1992 Buick Lesabre?

to left&just below water pump single bolt (10mm)once bolt is removed gently twist up&down as unit has rubber o-ring seal hope this helps


How can you get to the tcc on a Buick 3.8 2000?

How can you get to the tcc sensor on a 2000 buick lesabre 3.8 and can a speed sensor trigger a code for the tcc


Where is the location of the MAP sensor on a 1990 Buick LeSabre?

After consulting several sources, someone finally called a local Buick dealer who informed me that a 1990 LeSabre does NOT have a map sensor, it was the Mass Air Flow sensor that needs replacing.


What is wrong when a 1996 buick lesabre is not idling?

throttle positioning sensor


Where is mass air flow sensor for 1997 Buick LeSabre located?

The 1997 Buick LeSabre mass airflow sensor is located on the outside of the air intake housing. The sensor can be found on the right hand side of the air intake housing.


Does a 1995 buick lesabre have a camshaft positioning sensor?

I would think that any car without a distributor would have a cam sensor and a crank sensor. For the computer to send the fire signal to the correct spark plug it needs to know the position of both shafts. The failure of either of these will cause the engine to die. Older cars used the distributor to do this mechanically.


Where is the oil pressure level sensor on buick lesabre?

Oil level sensor is on side of oil pan.


Where is the twilight sentinel sensor for 2000 Buick Lesabre Limited?

probably on dash


Where is the O2 sensor on a 2000 Buick lesabre?

http://wiki.answers.com/Q/Where_is_the_O2_sensor_on_a_2000_buick_lesabre"


Would a bad coil pack cause a crank sensor code?

Yes it very well could, because a misfiring coil pack or weak coil pack can cause interruptions in the signals to both the camshaft position sensor into the crankshaft position sensor. I had this happen on my Buick LeSabre, it gave a code 18, which is Cam / crank position sensor error okay. I replaced all three coil packs, and it went away and never came back. If you look at the diagram for the wiring of your ignition control module, you'll see that the coil packs, ignition control module, and camshaft and crankshaft position sensors are all interconnected.


Where is the camshaft position sensor located on a 1997 Buick Riviera?

the sensor is located behind the pulley for the water pump has one single 8mm bolt in it u need to remove pulley to get at it


Where do you find the crank position sensor for a 1997 buick lesabre?

its behind the harmonic balancer attached by two bolts but you must first take off the balancer to get to it


What if the radiator fan doesn't work on 2004 buick Lesabre?

Sensor is likely bad


Where is the oxygen sensor on a 1990 Buick Le Sabre 3800?

The 1990 Buick LeSabre oxygen sensor is located on the outside of the air cleaner housing. The oxygen sensor will be on the back side of the housing.