Antifreeze and Engine Coolant
Honda Accord EX
Honda Accord LX

Where is the cooling system bleed valve of the 1990 Honda Accord EX?

789

Top Answer
User Avatar
Wiki User
2010-12-29 01:11:12
2010-12-29 01:11:12

Bleed valve is located on top of thermostat housing.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

With an evacuation pump; adequate hand operated models are available at the parts store.

User Avatar

It is cooling the engine off. Your Honda may be running slightly hot. I suggest you service the cooling system. Drain, flush, replace the thermostat, install a 50/50 mix of antifreeze & distilled water, bleed air from system.

User Avatar

how to bleed air out of cooling system 1997honda civic ex

User Avatar

how do you bleed a diesel peugeot cooling system

User Avatar

The cooling system is bled using the bleeder screw found on the thermostat housing. To find the thermostat housing on a 1998 Honda Civic follow the lower radiator hose to its outlet. While the cooling system is running loosen the bleed valve. When bubbles stop coming out the system has been bled.

User Avatar

How do you bleed the cooling system of a 1988 acura legend? Is there a bleeding screw and where is it located?

User Avatar

Any time you flush out the cooling system you need to bleed the cooling system.

User Avatar

You're simply going to have to have it removed and replace it. That nipple is at the lowest point in the system and there is no other way to drain it unless you have the system power flushed.

User Avatar

If the cooling system is in good working order the system will bleed the air out itself. If the system has a leak anywhere no matter how small the system will never bleed the air out.

User Avatar

there should be a air valve on the engine that you can bleed the bubbles out of the cooling system.

User Avatar

right at the end of the top radiator hose near the engine

User Avatar

You should not need to "bleed" it. The cooling system water pump circulates the coolant throughout the entire cooling system (including the cabin heater) and during the process any air in the system should migrate to the overflow tube and be exhauasted into the fluid overflow reservoir.

User Avatar

Engine cooling system is not a closed system you can't remove the air.

User Avatar

how do i bleed my accord v6 2000 coolant system, its has air and the rev's gone up & down......

User Avatar

The cooling system bleed valve, on your General Motors 5.7 liter engine, is located on the bottom of the radiator. The bleed valve should be in the middle of the radiator bottom.

User Avatar

You bleed the clutch at the slave cylinder located near the transmission close to the radiator up front.

User Avatar

There are various ways to bleed air from Clio cooling system. The best option is to run the system for a while with the cap up while making increased revs. รŠ

User Avatar

The bleed screw is by the thermostat housing it looks like a brake bleed screw

User Avatar

how does engine cooling system on berlingo 1.4 work

User Avatar

you dont bleed cooling systems you have to take it to a mech. shop or have the proper equipment and the r-134a on hand to do it your self.

User Avatar

There is no need to do this normally.

User Avatar

Should bleed all vehicles after the system has work done to it to get rid of air pockets

User Avatar

To bleed the cooling system on a 96 Acura 3.5 L, cool the radiator and remove the radiator cap. Loosen the drain plug and drain.

User Avatar

drain the whole cooling system and refill it. You will never know if you don't give details of your car!


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.