answersLogoWhite

0


Best Answer

The crank sensor is on the rear of the motor on the drivers side.It bolts to the bellhousing withe 2 bolts. It looks it has 2 wings on the sides where the bolts go through.It has a 2 wire plug going to it. Its easier to reach from the under side

User Avatar

Wiki User

โˆ™ 2005-02-03 04:01:12
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the crank sensor on a 1990 Jeep Cherokee and what does it look like?
Write your answer...
Submit
Related questions

Where is the crank sensor on a 96 jeep Cherokee?

The crank sensor mounts to the top of the transmission bell housing on a 1996 Jeep Cherokee.


If a 92 Jeep Cherokee will crank over but will not start what is the problem?

probably crank sensor, they are famous for that


Where is crank sensor on 99 jeep 4.0 grand Cherokee?

driver side on the back of the motor where is crak sensor on 94 jeep 4.0 grand Cherokee


How do you bypass a crank sensor in a Jeep Cherokee?

You can not. The crankshaft position sensor is required to run the engine.


Where is the cam sensor and where is the crank sensor on 2000 Jeep Cherokee Sport?

The cam sensor is inside the distributor. The crank sensor is on the top driver side of the bell housing.


Will a flex plate for a 1990 Jeep Cherokee Laredo fit on a 1992 Jeep Cherokee Laredo?

It should fit but, the crank position sensor produces a signal by referring to the flex plate. In 1991 Jeep went to a Chrysler fuel injection system and the windows that the crank sensor reads are different. So in other words it should bolt up but then it will not start.


How do you change crank angle sensor on 2000 Jeep Grand Cherokee?

LOCATION OF CRANK ANGLE SENSOR ON 2003 4.7 PETROL MOTOR


Will crank position sensor interfer with ignition module on a 1994 jeep Cherokee?

The ignition module uses the crank sensor to decide when to spark.


Where is the crank sensor on 1995 Jeep Cherokee v8?

Jeep Cherokee didn't come with a V8. It must be a Grand Cherokee? Top pass side of the bell housing.


Where is a crank sensor located on a 1991 jeep Cherokee?

Driver side of the bell housing.


Where is the output crank sensor located on a 1995 jeep Cherokee grand Laredo?

in a toilet


Does the 1997 jeep Cherokee have a crank sensor or a pickup coil?

It has both.It has both.


Where is the Knock Sensor on a 1990 Jeep Cherokee Sport?

what engine size


Where is the crank shaft sensor on a straight 6 94 Jeep Grand Cherokee Laredo?

The crank sensor is located on the top of the bell housing on the drivers side.


Where is crank sensor located on 96 Jeep Grand Cherokee?

The crank sensor is located on the back of the engine passenger side it bolts to the flywheel backing plate


Where is crank sensor on a 1993 Jeep Cherokee 5.2 l?

It should be on or near the throttle body.


How do you replace 1990 Jeep Grand Cherokee knock sensor 6 cylinder?

The Jeep Grand Cherokee didn't exist until 1993.


Do any one have a pic of a map sensor for a 1990 jeep Cherokee?

Below


Where is the crank position sensor on a 2000 jeep Cherokee 4.0?

The crankshaft sensor is on the top driver side of the transmission bell housing.


Where does crank sensor get power from on a 1996 jeep Cherokee 2.5l?

The PCM (engine computer) provides the power.


What would cause your jeep grand Cherokee to turn over but not start?

Bad crank position sensor


What would cause a engine bog down and back fire on acceleration on 90 jeep Cherokee despite timining and oxygen sensor being replaced?

the crank position sensor can cause similar symptoms jeep is known for crank sensor problems


Could a crank sensor cause a jeep Cherokee not to start?

Yes. The Crank sensor monitors the position and rotational speed of the engine to determine timing for ignition. if it is not functioning you will get no spark.


Where is the crank sensor located on a 1987 Jeep Cherokee 4.0?

From memory: My 1990 Jeep Cherokee 4.0L with a manual transmission has the sensor through the top of the transmission bell housing. Two bolts hold it in, and the 3-wire cable runs to a recepticle mounted on the firewall, near where the intake manifold meets the head.


Where is the crank sensor on a 1997 Jeep 4.0?

The crankshaft position sensor on a 1997 Jeep Grand Cherokee 4.0 L is on the top driver side of the transmission bell housing.