0
Where is the crankshaft position sensor located on the 1999 Mazda miata?
Wiki User
∙ 15y ago
Crankshaft position sensoer is on the right down side of the Crankshaft Pulley.
To advance the ignition to 14 degrees on '99. It's a matter to trick the ECU. How?, Repositioning the Crankshaft Position Sensor more upward. CPS is on the right down side of the Crankshaft Pulley. First, disconnect the CPS connector, remove the undercover, then remove the CPS bolt. Once out of the car proceed to enlarge the hole (bottom side) of the CPS bolt in order to get the upward reposition. Use portable Dremer to cut off ("bore") about 2-2.5mm from the integrated washer in the mentioned hole. Finally, install back the CPS having condider the following: Air gap between Pulley Plate teeths & CPS (Spec: 0.5-1.5 mm) and tightening torque of CPS bolt is 69.5-95.4 in-lbf. Past Specs were taken from the Miata'99 Workshop Manual.
After complete the installation. Use Timing light to check new timing. It should now oscillate between 14-16 degrees at idle instead of the factory oscillating 9-11 degrees."
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where is the crankshaft sensor on a 1997 Mazda Protege?
Answerthe camshaft sensor is the distributor but the crankshaft position sensor is located right next to the crankshaft its held on by one bolt
Where is the crankshaft position sensor located on a 2004 Mazda RX-8?
The crank position sensor is located on the front of the engine, behind the lower crank pulleys.
Where is the crankshaft sensor located on a Mazda B2500?
Hello! The crankshaft position sensor is located behind the crankshaft pulley,on the left side facing the front of the car.It is difficult to see and to remove it you need to remove the crankshaft pulley ( radiator,belts,.... )
Where is the crankshaft position sensor on a Mazda tribute 2004?
location cranckposition sensor mazda tribute 4cyl
Whats wrong with a 93 Mazda 626 that will crank but won't get fire?
On most 90s Mazdas the firing is controlled by the crankshaft position sensor that sends a signal to the ignition coil telling it when to spark, on v6 models the sensor is located underneath and to the right of the crankshaft pulley on the passenger side of the car.
Where is the gear position sensor located on a 2001 Mazda 626?
It's located in the engine compartment. Undernead the air filter. You can look under Throttle position sensor to view pictures of it.
Where is the camshaft position sensor on a 92 Mazda mx3?
It is located on the inside of the distributor . Three pin connector .
Where is the camshaft position sensor on a Mazda Miata?
On a 1999-2005 model Mazda Miata the camshaft position sensor is located on the valve cover towards the rear of the engine (closest to the firewall). It has one 3-pin connector connected to it and one 10mm bolt to remove the sensor
You have a2001 Mazda 626 that the alternator belt broke on changed the belt as well as the spark plugs and wires but now the car won't start the battery turns over but it doesn't start help?
Check your Crankshaft position sensor. Located on the right of the crankshaft. Probably got damaged when belt broke.
Where is the knock sensor located on a 1999 Mazda Millenia 2.5 engine?
Most knock sensors are located in the block on the firewall side. Should be the only sensor with two wires in the block. It will also have a camshaft position sensor as well. Hope that helps. I am not educated on Mazda engines.
Where would the knock sensor be located on a 2004 Mazda 6?
Where would the knock sensor be located on a 2004 mazda 6?
Where is the speed sensor located on a 1999 b3000 Mazda pickup truck?
99 mazda b3000 where is the speed sensor located
