0
Where is the location of the crankshaft position sensor on a Pontiac grand am 2.4 liter and how to install it?
Wiki User
∙ 16y ago
right above the oil filter
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you install crankshaft position sensor 95 mercedez Benz c220?
How do you install crankshaft position sensor 95 BENZ C220?
Install crankshaft position sensor on 2004 Maxima?
where is the crankshaft position sensor on a 2004 maxima
How do you install a crankshaft position sensor on a 2001 dodge diesel ram 2500?
ramdom much
Where is the camshaft position sensor on a 2002 Dodge Intrepid?
CRANKSHAFT POSITION SENSOR The crankshaft sensor is located on the passengers side of the transmission housing, above the differential housing Crankshaft Position Sensor The bottom of the sensor sits above the drive plate REMOVAL Disconnect electrical connector from crankshaft position sensor. Remove sensor mounting screw. Remove sensor. INSTALLATION Install sensor and push sensor down until contact is made with the transmission case. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque. Connect electrical connector to crankshaft position sensor.
How do you install a crankshaft position sensor on a 1996 Pontiac grand-amand where is it located?
If the engine is a 3100 V6, the crankshaft sensor is located behind the harmonic balancer (crankshaft pulley). You'll need a special puller to remove tha balancer. The sensor is attached by two bolts onto the timing cover. Replace sensor and plug it in. Repalce balancer& belts...you're done!
How do you replace the crankshaft position sensor on a Chrysler PT Cruiser?
The crankshaft position sensor on the PT Cruiser is on the side of the engine above the oil filter. The sensor is removed with two screws. Unplug the wiring, remove the bolts, then install the new sensor.
How do you install a crankshaft sensor on scion?
log on then you have to go to file then it should say install crankshaft to scion user. Click it then follow the instructions given.
How do you install a 1996 Pontiac Grand Am SE?
Install what?
How do you install a CrankShaft Sensor in a 95 Buick Century?
Pull the front cover off of it, Behind the Crankshaft balancer, The sensor is there. a diagram of how to install a creckshaft sensor.
How do you install a harmonic balancer on a 2003 corvette?
Crankshaft Balancer ReplacementTools Required* J41816 Crankshaft Balancer Remover * J41316-2 Crankshaft End Protector * J42386-A Flywheel Holding Tool * J41665 Crankshaft Balancer and Sprocket Installer * J36660-A Torque Angle Meter Removal Procedure# Remove the Air Conditioning (A/C) drive belt.# Remove the power steering gear. # Remove the starter motor.# Remove the right transmission cover and bolt. Notice:Refer to Fastener Notice in Service Precautions. Important:Make sure that the teeth of the flywheel holding tool mesh with the teeth of the engine flywheel. # Install the J42386-A and bolts. Use one M10-1.5 x 120 mm and one M10-1.5 x 45 mm bolt for proper tool operation Tighten the J42386-A bolts to 50 Nm (37 ft. lbs.).# Remove the crankshaft balancer bolt. Do not discard the crankshaft balancer bolt. The balancer bolt will be used during the balancer installation procedure. Important: For manual transmission applications, note the position of the crankshaft balancer before removal. The balancer does not use a key or keyway for positioning. Mark or scribe the end of the crankshaft and the balancer before removal. If replacing the crankshaft balancer, note the location of any existing balance weights (if applicable). Install new balance weights into the new crankshaft balancer (if applicable) in the same location as the old balancer. A properly installed balance weight will be either flush or below flush with the face of the balancer.# Mark or scribe the crankshaft balancer and the end of the crankshaft. Note the balancer installed position on the crankshaft for assembly.# Use the J38416-Band the J41816-2 in order to remove the crankshaft balancer. # Remove the J38416-B and the J41816-2 from the crankshaft balancer.# Not the position of any crankshaft balancer weights (if applicable). # Clean and inspect the crankshaft balancer. Installation ProcedureImportant:* The used crankshaft balancer bolt will be used only during the first pass on the balancer installation procedure. Install a NEW crankshaft balancer bolt, and tighten as described in the second, third and fourth passes of the balancer bolt tightening procedure. * The crankshaft balancer installation and bolt tightening involves a four stage tightening process. The first pass ensures that the balancer is installed completely onto the crankshaft. The third, and fourth passes tighten the new bolt to the proper torque.# Using the old balancer as a reference, mark or scribe the NEW balancer in the same location (if required). # Install balance weights into the NEW balancer (if required). Important:Align the scribe mark on the balancer with the scribe mark on the crankshaft. The balancer should be positioned onto the end of the crankshaft as straight as possible, prior to tool installation. # Install the balancer onto the end of the crankshaft.# Use the J41665 in order to install the crankshaft balancer. 4.1. Assemble the threaded rod, nut, washer and installer.Insert the smaller end of the installer into the frame of the balancer. 4.2. Use a wrench and hold the hex end of the threaded rod. 4.3. Use a second wrench and rotate the installation tool nut clockwise until the balancer is started onto the crankshaft.4.4. Remove the tool and reverse the installation tool.Position the larger end of the installer against the front of the balancer. 4.5. Use a wrench and hold the hex end of the threaded rod. 4.6. Use a second wrench and rotate the installation tool nut clockwise until the balancer is installer onto the crankshaft. 4.7. Remove the balancer installation tool.# Install the used crankshaft balancer bolt. Tighten the used crankshaft balancer bolt to 330 Nm (240 ft. lbs.). # Remove the used crankshaft balancer bolt. Important: The nose of the crankshaft should be recessed 2.40 - 4.48 mm (0.094 - 0.176 inch) into the balancer bore. # Measure for a correctly installer balancer. If the balancer is not installed to the proper dimensions, install the J41665 and repeat the installation procedure.# Install the NEW crankshaft balancer bolt. 8.1. Tighten the new crankshaft balancer bolt a first pass to 50 Nm (37 ft. lbs.). 8.2. Tighten the new crankshaft balancer bolt a second pass to 140 degrees using the J36660-A.# Remove the J42386-A and bolts.# Install the right transmission cover and bolt. Tighten the right transmission cover bolt to 12 Nm (106 inch lbs.). # Install the starter motor. # Install the power steering gear. # Install the A/C drive belt. # Perform the crankshaft position (CKP) system variation learn procedure.
How do to install oxygen sensor on 2006 Pontiac torrent?
We are asking how to remove and install a oxygen sensor for a2006 pontiac torrent.
Where is the crankshaft position sensor located on a 1999 Volvo v70?
It located on the drivers side engine compartment over top of the transmission you will need to remove the battery tray to install'
