answersLogoWhite

0


Best Answer
Copy

The belt tensioner is right in front of your alternator. You will see a big long screw going down in front of the alternator and to the left and underneath the screw you will see a bolt. Loosen the bolt and then loosen the screw and the belt should come off when you loosen it enough. Just did it not long ago on mine, very simple process.

User Avatar

Wiki User

โˆ™ 2011-09-13 11:14:24
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: Where is the tensioner pulley on a 1994 Lexus ES 300 and how do the belts come off?
Write your answer...
Submit

Related Questions

How do you relive the belt tensioner on a 94 galant?

You can relieve the tension on your 1994 Mitsubishi Gallant belt by loosening the tensioner pulley. The tensioner pulley can be loosened by turning the retaining bolt to the left.


Why is your new idler pulley squeaking on your 1994 GM Jimmy?

I assume you mean the idler pulley on your timing assembly, if this is the case then the belt is too tight loosen tensioner pulley. if you mean the automatic tensioner pulley for your alternator and A/C and the like, the you probably need a new tensioner] Good Luck


How do I change the power steering belt in a 1994 roadmaster?

Begin by loosening the tensioner pulley. Slide the tensioner pulley to the right. The power steering belt will become loose and can be removed. Put the new power steering belt on and tighten it by sliding the tensioner pulley to the left.


Where is the tensioner pulley on a 1994 dodge shadow 2.5 Ryan?

There is only 2 tensioner pulley on a Dodge Shadow 2.5L and that's right above the belt that drives the water pump and alternator... that tensioner pulley opperates the AC Compresser and the other one goes for the timing belt.


How do you remove the belt on a 1994 Jeep Grand Cherokee?

Put a ratchet on the tensioner pulley bolt... set your ratchet on "loosen" turn the tensioner pulley and assembly upword... hold it there and remove the belt... DO NOT LET GO OF THE RATCHET AFTER YOU REMOVE THE BELT slowly let the tensioner pulley move back to a resting position...


What would make a chirpping sound ina 1994crysler lebaron could it be the tensioner pulley and how do you replace it?

Noisy and chirpping soundS on a 1994 Crysler Lebaron could be as a result of the tensioner pulley and can be replaced by replacing the belt.


How do you change a serpentine belt on a 94 grand am?

You will need to loosen the tensioner pulley on your 1994 Pontiac Grand Am. The old serpentine belt will come loose and can be removed. Put the new serpentine belt on and tighten the tensioner pulley.


Where is the serpentine belt tensioner on a 1994 camaro LT1?

It's on the front of the engine and the belt rides on it's pulley, it's the pulley that you have to release to get the belt off.


How do you change the belt tensioner pulley on a 1994 Chevy Silverado?

Remove the belt, then remove the bolt in the center of the spring tensioner with a 15mm wrench, install new one


How do you change the alternator belt on a 94 GEO Prizm?

You can change the alternator belt, on your 1994 General Motors vehicle, by loosening the tensioner pulley. The loosened the tensioner pulley will create slack in the belt. Remove the belt and replace with a new belt.


How do you change the idler pulley on a 1994 explorer?

On the belt routing diagram under the hood (near the grille, but under the hood) you will find the location of the 'tensioner' pulley. You need to get a 15mm socket and place it on the bolt on the tensioner pulley. Then use a ratchet to put clockwise pressure on the bolt to loosen the tension on the belt. This will allow you to remove the belt from the idler pulley, remove the bolt, put on the new pulley. Now put clockwise pressure on the tensioner pulley again to put slack in the belt so you can slip it around the new idler pulley. You're done.


How do you disasemble a tension pulley to replace with a new one in a 1994 thunder bird?

Tensioner assembly removes with std. thread -- pulley itself is a left handed thread Clockwise to loosen


How do you install a serpentine belt on a 1994 Z71 305 Chevy engine?

Put the serpentine belt on to the pulleys of your 1994 Chevy engine. Tighten a serpentine belt with the tensioner pulley.


Where is the tensioner pulley in a 1994 ford escort lx?

The tensioner pully is just to the left of the alternator. It is an arm with a round pully on the end of it. It has a square 3/8 ratchet attatchment. It is about 7 inches long.


How do you replace the belts on a 1994 Nissan PU i cannot find the adjustment screw or tensioner pulley for any belt other than the alternator?

If you are talking about the secondary belt you will notice a pulley on the right side (driver's side) of the engine slightly below the level of the radiator shroud. That pulley has a nut on the face of it (14 mmi f I recall) and another behind it (same size it's a tensioner) loosen the front one and then use the back one (with a socket) to move the pulley down (loosening the belt). Then you can replace the belt. Use the tensioner to tighten the belt to the correct tension and then tighten the front nut thus locking the pulley in place. It should take you longer to snake the old belt out and the new belt in than adjust it.


How do you take out an alternator for a 1994 plmouth colt vista?

You loosen belt tensioner pulley, then take off the 2 mounting screws, then unhook wiring.


What is the pulley under the alternator in a 1994 Chevy caprice 5.7L and how hard is it to change?

Are you talking about the "idler pulley"? They are quite simple to change. Loosen the serpentine belt by using a socket on the center of the tensioner pulley, slide the belt off the idler pulley, use a socket to pull the center bolt of the idler pulley and replace the pulley with a new one.


Where is a serpentine belt routing diagram for a 1994 ford F150?

I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine There should be a sticker near radiator shroud that has belt routing. If not stick the belt down past the right side of fan/water pump .put belt on crank pulley then pull back of belt over water pump and then down around power steering pulley and up over compressor pulley. put belt from crank pulley around smog pulley then up to tensioner with back of belt around tensioner and then around alternator pulley.next put rachet and socket(15 mm) on tensioner and pull on it while placing belt under idler pulley.


Is air needed to change tensioner pulley on 1994 Mazda b3000?

I usually hold my breath when changing the pully, but some folks need air or they'll pass out.


How to adjust tensioner pulley on 1994 Pontiac grand am?

I JUST HAD MINE REPLACED.THEY ARE SPRING LOADED(AUTO ADJUSTING) THE PART WAS $65.OO AND LABOR WAS ONE HOUR.


How do you remove the crankshaft pulley in 1994 Lexus gs300?

Undo the crankshaft pulley bolt { anti clockwise } Then you will need a good strong puller to remove it. or try to move it by tapping the back of if fairly hard until it comes off.


How do you replace belts on 1994 Toyota corolla?

There is only one belt, the serpentine belt. You use a wrench to loosen the spring loaded tensioner and remove and replace, there is no timing belt it has a chain.


Why does the serpentine belt on a 1994 GMC Conversion van make noise?

It could be the belt or pulley bearing but also could be a pulley that is not level to the belt. The belt tensioner/pully could be out of angle by a few degrees or as in a lot of dodge caravans the main braket assembly/plate that holds the tensioner/pulley is warped and results in the entire tensioner to bolt on with a few degress more slant/level than proper and thus thus belt is always climbing/traveling or moving back and forth on the non grooved/flat/ portion support pullies.... usually being the tensioner pully which results in the squeeking noise..


Is changing the belt tensioner on a 1994 SL2 the same as changing a tensioner on a 1996?

Yep


How do you loosen a serpentine belt on a 1994 Jeep Cherokee sport?

If yours has a tensioner pulley, loosen the bolt at the center of the pulley slightly, then turn the tensioner bolt ( top ) clockwise, tighten the pulley when done. If no tensioner, you will want to tighten at the power steering pump. Loosen the top bolt on the power steering pump, and the bottom nut, both are facing toward the front, then loosen the two on the back of the pump, then turn the adjusting bolt to the desired tension on the belt, the adjusting bolt is below the pump facing the drivers side. The alternator will move when you do this.