0
Which direction do bolts turn to remove harmonic balancer on GMC 305?
Wiki User
∙ 10y ago
Counterclockwise off. Clockwise on.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Remove Taurus harmonic balancer?
Remove belt,4 pulley bolts and remove pulley. Remove harmonic balancer bolt and washer,reinstall bolt with out washer,just in about half way.You will need a harmonic balancer puller.These are not very expensive about $20.00 or borrow one from somebody.You just thread the correct included bolts into the balancer where you removed the pulley bolts and will be pushing on the reinstalled balancer bolt.The balancer should clear the bolt head without the washer.This is so you don't damage the threads in the crankshaft.
Is crank pulley same as harmonic balancer repair?
In most cases the crank pulley bolts to the balancer so the crank pulley would not be the same as the harmonic balancer.
How do you replace the harmonic balancer on a Chevy small block?
There is a bolt in the center of it, 5/8ths inch. Remove that, then the three 9/16ths bolts in a triangle pattern, which removes the pulley. Then, you will need a harmonic balancer puller, as they are pressed on.
Were is the crank sensor on a Pontiac grand pri?
The crankshaft position sensor is located behind the harmonic balancer. You will need a harmonic balancer puller and an impact wrench good for at least 750 ft pounds. Access the harmonic balancer through the passenger side wheel well. Remove the harmonic balancer center bolt and use the puller to remove the balancer. Use 1/4 - 28 X 3 inch bolts on the puller. The sensor is held with two screws. Be careful not to damage the weatherpack connector when releasing it from the sensor.
Where is the crankshaft sensor on 1995 buick regal 3.8l and how do you change it?
The crankshaft sensor is located behind the harmonic balacer. you will need a puller with special bolts to remove the balancer.
How do you Remove a Harmonic Balancer for a 1992 Oldsmobile 88 Royale?
The Balancer on that 3800 has a special puller that you use to remove it. The only difference is that the bolts for the puller have a much smaller diameter than the regular off the shelf puller. Be careful not to thread the bolts into the threaded holes too far or you could damage the crankshaft position sensor "pick up" fins on the back side of the balancer.
Toyota 4 runner 1990 harmonic balancer bolt turn?
The harmonic balancer on a 1990 Toyota 4 Runner is turned clockwise to loosen it. This is backwards from most bolts to prevent it from being loosened by the rotation of the engine.
Where do you find the crank position sensor for a 1997 buick lesabre?
its behind the harmonic balancer attached by two bolts but you must first take off the balancer to get to it
Where is the crank position sensor on 98 firebird?
On front of engine, lower right (facing front of engine) behind harmonic balancer pulley. It is held on by two bolts (must remove balancer pulley to remove) and is the last item on the wiring harness that runs over the front of the engine.
3.3 Buick century how to remove harmonic balancer?
1. Remove right front wheel. 2. Remove the cover from the inside fender. 3. Remove the small inspection cover between the engine and transaxle to expose the bottom of the flywheel. Jam a big screwdriver in a tooth of the flywheel and wedge it against the side of the opening and the floor or have an assistant hold it. 4. Use a big ratchet, at least a foot and half long and a cheater pipe another foot and a half to generate the 200+ foot pounds to remove the bolt from the center of the balancer. 5. Use a harmonic balancer puller to remove the balancer. A kit may not have the right size bolts to thread into the two holes in the balancer and you'll have to hunt for the right ones at a hardware store. They may be smaller in diameter than what come with the puller. Good luck. 2. The 3.8 Buick harmonic balancer requires a special puller. But, if you purchase three 4" long, 6mm diameter, 0.1 thread bolts and three heavy duty washers you can use a standard 3 hole puller to remove the balancer. The threaded holes for the 6mm bolts are about 2" inside the access opennings that are located on the face of the balancer. You will need to place the heavy duty washers on the 6mm bolts brfore they are used with the puller. The hex heads on the bolts are to small for the standard type puller and the washers will support the torque required to remove the balancer.
Timming mark on a 1997 Chevy 5.7?
There is a groove cut in the harmonic balancer. This is the part that the loer pully bolts to.
Where is the crankshaft sensor located on a 1991 Buick LeSabre custom?
to my knowledge it is located behind the harmonic balancer. You should be able to c the wires runing to it just to the right of the harmonic balancer. Now if you could help me with information on how to uninstall the harmonic balancer i would greatly appreciate it Thanks. To remove the harmonic balancer you have to buy or rent a harmonic bancer puller. The bolts required for yours may not be included. If not you will have to go to the hardware store and purchace them. You should use the 3 1/2 inch #8 1/4 inch bolt 3 required also buy 3 washers cost under 4 dollars.
