Want this question answered?
disconnect negative then positive remove rubber hold down and pull out
First you get to it then you remove it
To replace the thermostat on a 1998 Cadillac, locate the area you will be working in. The thermostat is located at the rear of the engine on the drivers side. Then locate the upper hose. Remove the upper hose from the housing and disconnect the unit. You can then safely replace the thermostat piece.
This usually is what I call a strut tower. USE CAUTION WHEN TAKING THIS ITEM APART AS THE SPRING IS UNDER GREAT PRESSURE AND WILL CAUSE INJURY. remove speaker grilland seat back extension, remove rear wheel. support the strut spindle, remove brake hose clip, hang brake hose out of way, remove bolts from strut base, remove upper nuts, lower the assembly and remove it.
* Loosen the front wheel lug nuts,raise the front of the car and support it securely on jackstands and remove the front wheels * Detach the brake hose bracket from the strut.If the car is equipped with ABS detach the speed sensor wiring harness from the strut by removing the clamp bracket bolt * Remove the strut to knuckle nuts and if nessary knock the bolts out with a hammer and punch * Separate the strut from the steering knuckle.Be careful not to overextend the inner CV joint dont let the knuckle fall outward as this may damage the brake hose * An assistant would be helpful at this point to hold the strut as the nuts are loosened.Remove the strut upper mounting nuts.Remove the assembly out of the fenderwell
Jack up the front of the car and support it on jack-stands. Remove the wheel and tire. Support the bottom of the axle stub and lower control arm with a jack. Remove the clip holding the brake line to the strut and slide the brake hose out of the tab on the strut body. Remove the two pinch bolts holding the strut to the hub carrier. Raise the hood, and remove the two bolts holding the strut to the top of the inner fender. Slowly drop the hub carrier assembly, steadying the strut so that it doesn
1986-1994 models # Loosen but dont remove the upper mount-to-shock tower nuts # Raise and support car # Remove the wheel and tire assembly # Remove the brake flex line-to-strut bolt # Remove the strut-to-knuckle pinch bolts # Using a suitable tool spread knuckle-to-strut pinch joint slightly # Using a suitable prybar place top of bar under fender apron and pry down on knuckle unil strut separates from knuckle be careful not to pinch the brake hose
How to I remove the heater core hose from my 1998 Mazda MPV from the motor. The hose is hidden from view. Can't get a tool or my hands inside the small space to remove the clip. Can you help me?
To replace the front struts on a 2000 model Hyundai Sonata, you will first need to remove the tires. There will be 3 nuts on top of the strut mount. You will need to remove the 2 bolts that connect from the strut to the knuckle. Then you will need to remove the ABS sending unit as well as the front brake hose. Once these components are removed, you can remove the strut. In order to remove the strut, you will need a special tool to compress the spring. Once the struts are removed, you can safely replace them with new struts.
Remove the lower radiator hose.
* Loosen the rear wheel lug nuts,raise the rear of the car and support it securely on jackstands and remove the wheels * Remove the brake hose clip from the bracket and disconnect the stabilizer bar link on the strut.If the vehicle is equipped with ABS remove the speed sensor harness bracket bolt * Remove the strut to knuckle nuts and knock the bolts out with a hammer and punch * Separate the strut from the knuckle dont allow the knuckle to fall outward as this may damage the brake hose * Remove the luggage compartment trim panel for access to the upper mounting nuts * Have an assistant support the strut and spring assembly while you remove the three upper mounting nuts.Remove the assembly from the fenderwell
* Loosen the rear wheel lug nuts,raise the rear of the car and support it securely on jackstands and remove the wheels * Remove the brake hose clip from the bracket and disconnect the stabilizer bar link on the strut.If the vehicle is equipped with ABS remove the speed sensor harness bracket bolt * Remove the strut to knuckle nuts and knock the bolts out with a hammer and punch * Separate the strut from the knuckle dont allow the knuckle to fall outward as this may damage the brake hose * Remove the luggage compartment trim panel for access to the upper mounting nuts * Have an assistant support the strut and spring assembly while you remove the three upper mounting nuts.Remove the assembly from the fenderwell