answersLogoWhite

0


Best Answer
Copy

Alternator belt is slipping. Tighten or replace as necessary.

2008-12-29 12:21:18
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

Why would a 1999 Kia Sportage Idle at 14 volts and when you raise the RPMS the voltage drops fast?

your alternater is most likely shot. if you replace it and the battery you should be good as new.


What is the zener breakdown voltage?

A: ZENERS are nothing else then regular diode that have a very predictable reverse breakdown voltage of xx volts. This voltage can be used to limit the input voltage or regulate on it.


What is the differnece between volts and amperes?

Voltage is power Amperage is current. you can have voltage but nothing runs without a closed circuit and then current flows.


What is the number of volts in mains voltage?

In the UK the mains voltage is 240 volts


What are examples of voltage?

220 volts, 110 volts, 440 volts, 400 volts, AC or DC voltage. High voltage like - 220 KV, 400 KV, etc


What happens when a 220 volts computer plugged into a 240 volts outlet?

Probably nothing bad. However, be certain that your computer is rated for this high of voltage.


Is voltage equaled to volts times amps?

Voltage is equal to volts. Power is equal to volts times amps.


What is the instantaneous voltage at 150 degree for a peak voltage of 380 volts?

316 volts.


What is the voltage in Hawaii?

The voltage is ~120 Volts.


Can you use a 220v fluorescent tube on a 110v ballast?

It is not a fluorescent tube that is voltage rated, it is a ballast that is used to raise the secondary voltage to fire the tube. If your working voltage is 110 volt and the voltage required for the ballast is 110 volts then the tube should work in the fixture. You can not apply 220 volts to a 110 volt ballast as it will destroy the ballast.


How many volts is low voltage electricity?

Low voltage by definition means any voltage from 31 to 750 volts inclusive.


What is the voltage drop across a 12 ohm resistor with a source of 24 volts?

If there's nothing else between the ends of the resistor and the power supply, then the voltage across the resistor is 24 volts, and the current through it is 2 amperes.


What is the conversion from RMS voltage to peak voltage?

The average voltage is the rms voltage.Volts peak = volts RMS times 1.414Volts RMS = volts peak times 0.7071Use the link below to an RMS voltage, peak voltage and peak-to-peak voltage calculator.********************************The average voltage is not the r.m.s. voltage.The average voltage of a sine wave is 0.636 x the peak value. Conversely, peak voltage is 1.57 the mean or average.


Can 110 volts appliances be used in a 220 volts country?

Not without a voltage adapter to change the 220 volts into the voltage the appliance needs.


What is the volt drop across a 10k resistor with a 5 volt supply?

If there is nothing else in the circuit, then the voltage drop across the resistor will be the full supply voltage of 5 volts. The size of the resistor does not matter in this case - it will always be 5 volts.


How much voltage requred computer to run?

2 volts, 5 volts, 12 volts. New computers need even less voltage.


Voltage is measured in what?

volts


What is voltage measured in?

volts


What are the units for voltage?

volts


Voltage has the units of what?

...volts.


How do you change a battery voltage to a 9-volts?

Batteries are MADE to deliver a specific voltage you can not change this retrospectively.


How do you convert 415 volts to 240 volt?

The voltage of 415 volts is a 50 hertz country voltage. The three phase wye connection of this voltage is 240 to ground. 415volts / 1.73 = 240 volts.


What is the current drawn when you have a single phased load of 200KW is supplied at 500v through an overhead line with a resistance of 0.1ohm per conductor?

If the voltage is 500 volts, and the power is 200 kilo-watts, then the current is 400 amperes. (Watts equals Volts time Amperes)The resistance of the conductor has nothing to do with this calculation, but that fact that the conductors are 0.1 ohms means that the voltage drop across each conductor is 40 volts. (Volts equals Amperes times Ohms) Since there are two conductors, the total voltage drop is 80 volts, and the voltage available to the load will be 420 volts.


What is the voltage of telephone line?

The standard voltage for the telephone system is 48 volts DC. Ringing voltage is much higher, around 90 volts AC at a low frequency. When you place a load of about 600 ohms on the line, you are "off hook" or connected. Telephone ringer voltage is 50.5 volts at standing and -50.5 volts at ringing


Voltage difference is measured in amperes?

NO! voltage is measured in volts!