Mitsubishi Montero, Pajero, and Shogun

Why does the check engine and brake light stay on a 2000 Miisubishi Montero Sport?


Top Answer
User Avatar
Wiki User
2009-09-07 02:57:11
2009-09-07 02:57:11

i have a 2002 montero sport i had the same issue i replaced the brake pads first no luck 2 days later i had to replace the alternator after that both lights went off


Related Questions

The parking brake light stay lit on the 1999 Mitsubishi Montero sport the parking brake is working and you have not put the light off.

Should be located at the upper end of brake pedal under dash area

Remove the tire and wheel from your 1997 Mitsubishi Montero. Remove the brake shoe assembly. Tap on the rotors to loosen them. The rotors will slide off. Reverse the process to install your new rotors.

Look at the upper end of the brake pedal under dash area

You will need to remove the tire and wheel from your 2002 Mitsubishi. Remove the brake pad spring. Remove the brake caliper. Reverse the process to install the new brake pads.

check the fuse box under the hood in the engine compartment

I don't have a 2001 Montero Sport, but I just recently bought a 1998 Montero Sport and it had this problem while I test drove it over night. I told them to fix it before I would buy it and they did. It was some problem with the actuator or whatever engages the transfer case, they had to replace that part, and fix something in the brake system in the engine compartment. It took about 1-2 weeks to fix and a $1000 or so (out of their pocket of course). The basic problem was that the transfer case had trouble staying enagaged and when it did, it knocked out the ABS system. If you do have it fixed though, be sure to check your brake connections in the engine compartment, as they hadn't tightened down a connection enough and I had been losing brake fluid. Sorry, to answer your question, it most likely means a repair to your transfer case components and your brake distributor block in the engine compartment Sorry, if I got any terms wrong!

you'll need to pop off the grease cap then remove the snap ring to get the hub off to get the rotor off.

put your car in reverse and pull the hand brake. done

Check your brake fluid level in the brake master cylinder in your engine compartment when it is low your brake warning light will come on

I have an 02 and it is located to the left of the brake. Take off the cover and it was the one below the top right fuse(it is a ten amp fuse in mine)

Lift up your cart using jack stands for safety. Remove the wheel and take the brake hose off of the caliper body. Remove the two pins that secure the caliper to the bracket and pull of your rotor.

In a 2002 Ford Explorer Sport : You check the brake fluid LEVEL in the brake fluid reservoir in the engine compartment . It is on the drivers side of the vehicle , near the firewall ( that's the metal wall that divides the engine compartment from the passenger compartment ) It is a plastic reservoir that allows you to check the brake fluid level just by looking ( you only need to remove the cap if the brake fluid level is not up to the full mark and you are going to add the DOT 3 brake fluid that is required

The brake light in your dash will turn on if the brake fluid level is low in your brake master cylinder in your engine compartment

defective brake light switch. crawl into the drivers side and look for a simple push button switch above the break pedal(switch will be covered by the bar until you push the brake down). Check the switch is moving... replace or unjamm the switch...

The engine does not have to be running to release the parking brake on your 1994 Cadillac Seville. The parking brake can be engaged or released without the engine running.

When Exhaust brake is on squeak noise comes from the engine?"

you can check a few things... 1) check if the switch that is activated when you use the emergency brake light is working or not. maybe it got stuck 2) check in the brake flud reservoir. do you have enough fluid? if so, the rubber in the cover is folded or unfolded? it should be folded, if not, it will be hitting another switch and triggering that light

You're talking about an engine compression brake, commonly referred to as a Jake Brake.

The engine computer through the brake light switch.The engine computer through the brake light switch.

the brake resevior should be located on the driver side against the firewall,clear round cylinder with a white lid ,about 4 inches in diameter

Brake horse power is the amount of engine power which makes it to the wheels. This is different from the actual output at the engine.

check fuses then check all the bulbs, then check the turn signal switch the brake lights work through it

If you mean by speed and wether or not it is a production car, then it is the bugatti veyron super sport, it has a 16 cylinder engine with 4 turbo chargers. It produces 1001 bhp and an air brake witch is very powerful

Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.