Why does the harmonic balancer on a 1994 Pontiac Bonneville ssei supercharged keep breaking?
The most common reason for the harmonic balancer breaking on a 1994 Pontiac Bonneville SSEI is the inner and outer mass is breaking the balancer down. This happens because your engine is running rough or too high of RPM's.
I'd have to hire a mechanic
The balancer is attached to a flywheel that drives the serpentine belt for the water pump, power steering, etc. If harmonic balancer doesn't work, belt won't run, and eventually, neither will the car.
behind the harmonic balancer pulley, i believe.
i have a 92 bonn. and my car wasnt starting and it turns out it WAS the crankshaft sensor and the harmonic balancer
What would cause a 1990 Bonneville to rattle near the belt when stopped in or out of gear but not when accelerating or having the RPM's reving at 1.5 or higher?
remove the right front tire should be directly behind to yhe left of the airconditioning commpresser this is a Pontiac 3800.
With a harmonic balancer puller.
do the harmonic balancer have a seal for anti-freezer
Harmonic balancer replace
A bad harmonic balancer can cause a knocking noise. The harmonic balancer doesn't actually produce the noise, but it can cause the noise in the engine.
The harmonic balancer tool is made especially to remove the balancer. Some stores will loan you the tool with a deposit.
If you meant harmonic balancer keeps going bad you probably have a bent pulley.
hay i am jitendra haldar can you Harmonic progression explane with examples
The harmonic balancer is located on the front of the crankshaft
how to replace harmonic balancer on a 2000 infiniti i30
how to replace harmonic balancer 3.4 v6 2001 grand am gt?
Harmonic balancer is bad and will need to be replaced.
On any motor, the harmonic balancer is on the front of the crankshaft. It is what the pulley is bolted to.
In most cases the crank pulley bolts to the balancer so the crank pulley would not be the same as the harmonic balancer.
Go to Autozone and tell them u need a harmonic balancer puller
No, a rusted harmonic balancer will not prevent the engine from turning over.
With a balancer puller tool. With a balancer puller tool.
The harmonic balancers function is to reduce vibration between the engine and the crankshaft. To replace the harmonic balancer requires a specific tool available at an auto parts store. Loosen the crank pulley via 4 bolts to access the balancer. Using the tool remove the harmonic balancer from the crankshaft.
The flywheel has to be held in place by a holding tool, Remove the mounting bolt, then use a balancer remover to pull the harmonic balancer.
Why would a 1989 Pontiac Bonneville continue to cut off at stops if the check engine light is on but you have replaced the starter battery coilpack spark plugs and wires?
I HAD A 1990 BONNEVILLE I HAD THE SAME PROBLEM WITH.IT TURNED OUT TO BE THE CRANK SENSOR.ITS BEHIND THE HARMONIC BALANCER. HOPE THIS HELPS
You will need special tools like: harmonic balancer puller, and impact wrench.
You need a harmonic balancer puller, and a 1/2 in drive inpact wrench.
To remove the harmonic balancer from a Nissan Maxima, first you need to removed the center bolt. After that, you can use a puller to remove the harmonic balancer. Before you do this, make sure you disconnect the battery and remove the drive belts.
On most newer cars, the crank pulley is one piece with the harmonic balancer.... Remove it with a harmonic balancer puller.
Only if your Harmonic Balancer is unlike anyone elses out there.
use a harmonic puller
first jack up and support the front passengers side of the van then take the tire off then take the plastic splash guard off then you should be able to see the harmonic balancer from the wheel well opening then your going to need to take off the belt then put a harmonic balancer puller on it and crank it out harmonic balancer puller is absulutely needed to take the balancer off of you could… Read More
there is a speacel tool called a harmonic balancer puller, you can pick one up at your local carquest.
The crankshaft pulley unbolts from the harmonic balancer. The harmonic balancer can be removed from the crankshaft with a 3 bolt puller.
Remove the belt. Remove the bolt that attaches the harmonic balancer. Rent or purchase a harmonic balancer puller. Follow the Instructions with the puller and remove the old balancer. Install the new balancer making sure to line up the keyway, a little oil helps. Put the retaining bolt back in and tighten to manufacture specs.
take off the serpentine belt and crank pulley and you will need a harmonic balancer pulley to get it off.
8 inch balancer.
loosen the center bolt and get your self a harmonic balancer puller just make sure you loosen the center bolt enough but not too much but you need a balancer puller.
Am unsure of what you are asking. The harmonic balancer is a lifetime part of the engine and does not need replacement based on a time or mileage requirement.
The crank sensor is located behind the Harmonic balancer. Try not to break the rubber within the Harmonic balancer when removing or on the safe side replace both the Crank sensor and the Harmonic balancer ( the big pulley on the bottom - most part of the engine.)
No there is not.
The harmonic balancer does require a puller if that is what you are asking. The harmonic balancer does require a puller if that is what you are asking.
Not too familiar with that engine, but never use a hammer to press it on. Go to your local Kragen, Shucks or autozone, they have a harmonic balancer installer in which you can rent. It simply screws into the center of the shaft and evenly presses the harmonic balancer onto the crankshaft.
When replacing water pump on 95 contour 2.0l engine harmonic balancer seems to be in way cant get it off how do you do this?
Pull the retaining nut then use a puller to remove the harmonic balancer.
With a harmonic balancer puller. Your local auto parts store can sell or rent you one.
first remove serpintine? fan belt then remove large bolt in middle of harmonic balance. this bolt usually has left hand thread next with a harmonic pulley ,puller, remove harmonic balancer.when removing this, there is a key in the balancer and shaft if a new key did not come with new balancer,make sure not to loose the old one install new balancer with key.use the bolt to pull balancer up tight where it needs to be… Read More
The crankshaft position sensor is located behind the harmonic balancer. You will need a harmonic balancer puller and an impact wrench good for at least 750 ft pounds. Access the harmonic balancer through the passenger side wheel well. Remove the harmonic balancer center bolt and use the puller to remove the balancer. Use 1/4 - 28 X 3 inch bolts on the puller. The sensor is held with two screws. Be careful not to damage… Read More
Remove belt,4 pulley bolts and remove pulley. Remove harmonic balancer bolt and washer,reinstall bolt with out washer,just in about half way.You will need a harmonic balancer puller.These are not very expensive about $20.00 or borrow one from somebody.You just thread the correct included bolts into the balancer where you removed the pulley bolts and will be pushing on the reinstalled balancer bolt.The balancer should clear the bolt head without the washer.This is so you don't… Read More
buy a new harmonic balancer which is less than 60.00 at your nearest auto parts store loosten belt out of the way,pull off old balancer with a puller ,reinstall reverse
You need a balancer puller to remove it , It don't just slide off.