0
Why is your brake pedal very tight when it is cold out on your Nissan Pathfinder?
Wiki User
∙ 15y ago
This happens in most cars w/ older brake fluid, and it can also happen w/ the Power Steering fluid. Over time, these two fluids absorb water. At a certain point, they have absorbed enough water that a freezing effect occurs. It is usually not total, and allows for some stopping power. However, if this happens, and allowing the car to warm up while pumping the brakes don't help, then you should have your fluids changed, possibly even flushed.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Why is your brake pedal tight?
check the master cylinder.
Why would the brake lights be stuck on on a 1998 Ford Contour?
It is because the switch on brake pedal has been moved. It must be pushed by the pedal all the time, and when you push the brake pedal, the button switch comes out, and then you should turn your lights on. This switch is tight by double nut next to the pedal, so disconnect it, release the tightened nut, or verify that it is tight, make sure it is pushed by the pedal every time this one is up, make a turn if needed to make tight again.
Why is vehicle brake bled?
they are bled to remove air out of your brake system. bleeding prevents you from having mushy brakes or your pedal going to the floor. it also makes the pedal tight and more sensitive to your feet.
What is wrong if a car won't turn over brake pedal is stuck and steering wheel is tight?
could be your ignition
Why is my brake pedal not tight after changing pads on a 1994 cadillac concourse?
You may need to have the brakeline bled (drained of brake fluid) and add new brake fluid while making sure brakeline is air free. This is usually done by pumping the brake until the pedal becomes appropriately firm . Hope this helps .
How do you bleed brakes in 1978 Chevy pick up?
On the front brakes you will see the caliper on the backside of it it will have a small valve that looks like a grease fitting. Remember it is the one on the caliper it self. Get someone to bump the brakes up tight. Once they have them tight hold the brake pedal down. While the brake pedal is held down use a wrench to brake the bleedervalve lose. once you do look for bubbles in the fluid. repeat intill bubbles are gone. Same way on the backs.
How do you adjust the pedal assembly on a VW bug The clutch pedal hits the floor on a VW bug after you change the pedal assemby.?
When you put in the new assembly, hold the pedal up straight so the cable doesn't unhook from the assembly. Then have some one in the back put the cable tight and screw the wing nut on until its tight then let go of the pedal their you have it. put the pedal in an out to make sure it tight if it feel back down then you didn't tighten it enough in the back.
Would tightening the belt too tight cause the fan clutch to go out on a 92 pathfinder?
no
What should the torque be on a brake chambing ring?
Tight is tight... get it snug, roll with it.
How do you bleed brakes clockwise or counter clockwise?
The Bleeders Will Open Counter Clockwise, Just The Same As Removing a Bolt. Make Sure You Put Some Penetrating Spray On Them If They Are Feeling Real Tight ( not WD-40 ) A Good Brand Also Use A 6 Point Socket, Or Wrench And Take Your Time. The bleed valve is turned COUNTER-CLOCKWISE to bleed air from the brake lines. You'll need someone to press the brake pedal as someone else turns the valve to let air/brake fluid out. Once the pedal is down as far as it will go, turn the valve back closed, then the pedal should be let back up. Repeat that process until the brake pedal is firm. Make sure you keep the brake fluid reservoir full.
What caused the right front brake to lock on a 91 Toyota 4 runner?
You have a rusty brake caliper. The piston is probably so rusted that its so tight for the piston to retract everytime you release the brake pedal. The only remedy for that problem is to buy a new or rebuilt caliper and replace the defective one...........You might want to consider replacing both....
How do you bleed brakes on a 1997 Cavalier?
Unscrew the brake line from the drum or the caliper. Dont let the brake fluid drain. Have some one step on the brake pedal and while it is gushing out fit it back on and screw it tight. There are one person bleeders which suck the brake fluid through so you don't need another person. These look like a kidney with a tube and they are available at auto part stores.
