0
Why would the clutch not retract after you push it in on a 1988 Mazda B2000?
Wiki User
∙ 15y ago
There is air in the clutch hydraulic system. This can be because the Master or Slave is bad, low fluid level, or it was not completely bled after installing a Slave or Master. Usually this problem is caused by a bad clutch slave which has leaked out all of the fluid.
Kyrasis6
Owner of Mazdatruckin.com
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where can I purchase auto parts to repair a Mazda B2000?
One could purchase auto parts to repair a Mazda B2000 from the Mazda B2000 Auto Parts online catalog. Other places to purchase auto parts to repair a B2000 would include O'Reilly Auto, Advance Auto Parts and also Auto Parts Wearhouse.
What would cause no spark to a coil in a 1986 Mazda b2000?
I have replaced the coil and distributor cap.
Could a tall person fit in a Mazda B2000?
I see no reason why a tall person would not fit in a Mazda B2000 because the seat can be slid back. If the person is extra tall, perhaps an extended cab would be best because the seats will slide back further than in a standard cab.
Does a 1985 mazda rx7 have a hydrolic clutch?
From the factory yes it would have a hydraulic clutch ! If not it has been modified at a later date .
Where is the clutch fluid after leaking on a 1986 Mazda B2000?
Normally if the clutch fluid reservoir is low the slave cylinder is leaking at the transmission on the right hand side.Check the fluid level then check the slave and if it's leaking it will be there and typical visual is cracked rubber boot coated in brake fluid.Result to fix replave this part and bleed it as you would brakes,there is a bleeder screw on the slave cyldr and have another person pump the clutch pedal to remove excess air out of system.
Would a bad clutch fan on a 1994 Mazda B3000 cause it to overheat?
Yes it could.
Why would a 1995 Mazda 626 stall everytime you depress the clutch?
You may have some bare wires that are shorting out on the clutch pedal. Get under the dash and check it out.
How do you set the points on a Mazda B2000 1986?
This truck DOES NOT have points!!You would have the standard rotor cap and distributor for electronic ignition.Just buy new cap/rotor install and DONE.Points have not been on vehicles for YEARS.
How much is insurance for a 2006 Mazda RX-8?
You would be looking around £500 mark at a clutch spec, dealer maybe double.
How do you repair a 1986 Mazda b2000 clutch?
If the clutch is slipping or not going into gear or specific gears, replacing the clutch assembly,and throw out bearing is a good idea.This task requires removing the transmission from the truck and takes several hours to do.I would suggest if you are considering doing this you should be mechanically inclined due to the time,knowledge it requires to do this correctly.Short if you do not have the time or tools etc,take it to a shop for a reasonable cost.I have done this task and it is pretty simple and using a chiltons or haynes manual helps alot.But unless you do have the mechanics go the shop route to save the headache or problems.
Clutch is sticking on Mazda 86 b2000?
Things to check first are is the clutch fluid reservoir low?Second check at the transmission on the right hand side at the slave cylinder for it leaking and note(fluid would be low in the reservoir).Mazda trks are notorious for slave cyldr failure.Now if the fluid is not low and the slave is not leaking things to consider.Now do you here any noise coming from the transmission while in neutral ONLY,and once you depress the clutch pedal the noise goes away(if so the throw out bearing is going bad)I would not say the clutch is need of replacement IN most cases based on on a sticking clutch pedal.Probably the clutch master is going bad(spring is weak inside assembley) and the fluid level is fine,no leaks at the slave cylinder and what you need to do is REPLACE the clutch master cylinder!I do not recommend a rebuild go to auto zone they sell the whole unit with the reservoir,and you will have to bleed the air out at the slave cyldr once installed.Typically with this issue the pedal sticking is low fluid,leaking slave clydr,or a bad clutch master clydr.Worst case is you need a new clutch,or throw out bearing and pressure plate.Normally a failing a clutch it will slip in any gear and or not shift into a particular gear.Try the simple stuff first over a new clutch/bearing assembly.
What would make your clutch slip on a 2001 Mazda 626?
Auto trans: low hydraulic pressure, possibly from a faulty valve body, damaged pump, blocked filter or leaky o-rings. Manual trans: worn clutch disk, oil on clutch disk.
