0
No, a breaker is an amperage activated device.
Wiki User
∙ 10y ago
No, cobwebs alone will not trip a breaker. Breakers are designed to protect against overloading and short circuits, not cobwebs. However, if the cobwebs accumulate and cause insulation damage, it could potentially cause an electrical issue that may trip the breaker. Regular cleaning and maintenance can help prevent this.
Add your answer:
Earn +20 pts
If a shunt trip occurs does breaker go to off or trip position?
the breaker goes to trip position
Does a hot day trip a circuit breaker?
The ambient temperature does have an effect on the tripping point of a breaker. If a breaker is operating at near capacity the additional ambient temperature will lower the breaker trip set point.
How much current flows through circuit breaker trip coil?
The trip coil has the whole circuit load amperage flowing through it. Thepurpose of the breaker is to only allow current up to its trip point. That is the only way that the breaker can sense if the current is within the limit rating. If the circuit load amperage becomes greater that the breaker rating it will trip. The trip coil that you refer to is a magnetic trip which senses the magnetic field that surrounds the wire. Breakers also have a thermal trip which senses a heat build up on the current flowing through it. If the breaker is in a high ambient temperature it will lower the rating on the breaker.
When a shunt trip breaker trips does the voltage remain on?
No, it does not have voltage in trip position.
A GFCI device in a breaker is intended to?
A GFCI device in a breaker is intended to trip the breaker open when a ground fault is sensed in the circuit that the breaker is protecting.
If a shunt trip occurs does breaker go to off or trip position?
the breaker goes to trip position
Can a shunt trip breaker be tripped from to different emergency buttons?
Yes a shunt trip breaker can be activated manually.
How do you detect if a shunt trip breaker is malfunctioning?
The way to detect if a shunt trip breaker is malfunctioning is to manually trip the breaker. The shunt is usually wired through a auxiliary relay. Make sure that before you trip the breaker that the load can be shut off without taking a production line etc. off line. Trip the auxiliary relay using a test jumper to activate the relays coil. The breaker's handle will move to mid throw and the load will disconnect from the supply power. If the breaker trips then it is working properly. If the breaker does not trip trouble shoot the circuitry that is used to trip the breaker. Usual problem is an open circuit.
How much does a shunt trip breaker cost?
The cost of a shunt trip breaker depends on the amperage and number of poles the circuit connected to it needs. The cost of the shunt trip over a conventional breaker is substantially more.
What are the breaker ampere trip ratings?
The ampere frame rating for a circuit breaker designates how the circuit breaker should be configured. It also states the trip unit of the amp.
Does a hot day trip a circuit breaker?
The ambient temperature does have an effect on the tripping point of a breaker. If a breaker is operating at near capacity the additional ambient temperature will lower the breaker trip set point.
Does the power supplied to trip shunt trip breaker have to be applied momentarily or can it latch?
A shunt-trip breaker trips when voltage is applied to the coil. It does not self-reset when the voltage is removed, the breaker must be reset manually. The trip voltage can either latch or be applied momentarily, but must be de-energized before the breaker will reset.
Can a thermostat cause a breaker to trip?
If it is a line thermostat and it is connected across the line instead of in series with the load then yes it will trip the breaker.
What is transfer trip protection scheme?
A scheme where a signal is sent to to a remote location to cause a trip. An example could be a breaker failure scheme. When the breaker is told to trip, and fails to do so, fiber communications could be used to transmit a trip signal from the local substation to the substation the next bus out to cause that breaker to trip.
How do you reset a shunt trip breaker?
A shunt trip breaker is reset the same way as an ordinary breaker, move the handle to the full off position and then to the full on position. First check the tripping circuit, sometimes a latch relay is used to hold the breaker shunt trip coil in the trip position. If this is the case then reset the latch relay first.
How much current flows through circuit breaker trip coil?
The trip coil has the whole circuit load amperage flowing through it. Thepurpose of the breaker is to only allow current up to its trip point. That is the only way that the breaker can sense if the current is within the limit rating. If the circuit load amperage becomes greater that the breaker rating it will trip. The trip coil that you refer to is a magnetic trip which senses the magnetic field that surrounds the wire. Breakers also have a thermal trip which senses a heat build up on the current flowing through it. If the breaker is in a high ambient temperature it will lower the rating on the breaker.
When a shunt trip breaker trips does the voltage remain on?
No, it does not have voltage in trip position.
