0
You have a 1991 eclipse and when its cold the engain will start but wont stay running but if you unhock the mas sencer it will run fine but when its warm you got to plug it in and it will jerk around?
Wiki User
∙ 18y ago
If it looks like a duck and tastes like a duck, it might just be a duck. Sounds like you need a MAF sensor.
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
What can make a 2000 Mercury Sable 3.0 dohc run lean?
the o2 sencer, temp. sencer, or the air temp sencer can. the o2 sencer, temp. sencer, or the air temp sencer can.
When was David Sencer born?
David Sencer was born in 1924.
When did David Sencer die?
David Sencer died in 2011.
What does tha crank sencer do?
What will be the sign when the crank sencer is not working?
How do you install the crankshaft position sensor on a 1987 Buick Grand National?
rotate the engine until you have the gape on the interupter ring over the crank sencer. remove the crank sencer assembley that bolts to the block with the sencer attached. ( do not take the 5/16 bolt loose that holds the sencer.(unplug the wires to the sencer first. once yu have remover the sencer assembley from the block you can tell how to set up the new sencer. mark the sencer with a knife or paint pen so you can see how to set up new sencer. Now you are readty to remove the 5/16 bolt. back the bolt out and remove the sencer for the bracket. pay attention where you marked the old sencer. Mark the new sencer in the same location and place it back in the bracket,( Be sure to alighn the sencer exactly as the old on. Then tighten the 5/16 bolt back..DO NOT over tighten this bolt. now reinstall assenbley back onto the block. Be sure not to break the window of the new sencer as you reinstall. it will be a tight fit but it will go. Take a flywheel tool and turn engine BY HAND to make sure you have properly set up your sencer. As long as it does not hit it will be good. if it does hit, back off the 5/16 bolt and move the sencer until it does not make contact with tha interupter ring on the crank shaft. plug your wires back into the sencer. start engine an have fun.. Hope this help.
Where is the 1999 Acura Integra cooling fan sencer?
1999 fan sencer for acura integra
Why does your 92 4 runner run rough for about 5 to 10 seconds then smooths out also smell gas fumes when running rough?
Does it have a Carb.? Choke sticking and running rich could be your throttle posioning sencer is starting to go drive safe
Where can you get the cheapest co2 sencer?
Try Amazon.com
Where is the heat sencer located on the engine?
on the top
7 How do the automatic doors at a supermarket know when to open and close?
The doors have a black thing at the top of them. Inside that thing is a sencer and when you walk in to the sencer the doors open.
How do you fix the speed sencer on 1997 Honda Civic Lx?
The speed sencer reads off of the diferential and is located on the top of the transmision. It has a wire pluged in to it facing strait up. Remove the plug and simply removed the sencer with a screw driver. If these go bad you will get an eradic reading on the speedo or it simply will not work at all. Also the V-tec and when the trans will shift on an auto is controled by this sencer. If the sencer is unpluged the trans will shift normal but you will have no V-tec, [[User:67.49.132.104|67.49.132.104]]Hope this helps[[User:67.49.132.104|67.49.132.104]]
Can you bypass a crank sencer on a 1997 Chevy truck?
No you can not.
