0
You have changed the starter and battery in your 1984 Mazda 626 all you get is a clicking sound but car will not start unless pushed any Ideas?
Wiki User
∙ 12y ago
suspect starter relay locate relay and replace temp solution run wire straight to battery from starter make sure in neutral when starting
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
When the starter button is pushed on 2003 Honda Fourtrax 350 what causes it to click?
dead battery
I recently had the battery checked-It is in working condition. Today I tried to start the bike and the lights went dim when I pushed the starter button all that happened was a series of clicking nois?
That's the sign of a discharged battery. Why? Charging insufficient? drain when everything is supposed to be off?
What can cause a 1991 escort with manual transmission not to start unless it is pushed?
The battery, cables and starter may be bad.
How do you change battery Sequoia key fob?
The battery in the key fob of a Toyota Sequoia is changed by using a coin to separate the two halves. The coin style battery can then be pushed out and a new battery put in.
How do you change key fob battery honda?
The key fob battery for a Honda vehicle is changed by removing the retaining screws and gently popping the rear cover off. The battery can then be pushed out of its holder and a new one installed.
Can hear clicking sound when button pushed?
Don't push that button.
Why will my 1986 Nissan 300zx NA start and then die?
check all your battery connections and battery, then check your starter wire. mine was lose and the car wouldn't turn over my dad pushed it in while i was trying to start it and it cranked right up
How do you install a crankshaft position sensor on a 2000 Oldsmobile Intrigue?
This is a quick answer. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wore plug into the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery. If you have ever removed or replaced a starter this is cake, that is the hardest part of the job. Rich
How do you remove and replace 2000 intrigue crankshaft sensor?
This is a quick answer. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wore plug into the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery. If you have ever removed or replaced a starter this is cake, that is the hardest part of the job. Rich
What is a jack shaft on a Harley Davidson?
A jackshaft is an assembly that connects the starter shaft/spline to the starting gear. When the starter button is pushed a pinion gear (part of the jackshaft assy.) engages the starter gear spinning the starter gear.
How do you rewire a starting system on a 1993 sea doo sp jet ski and how does the system work it has a new solenoid and starter is good but it wont turn over?
is the safety ignition switch for lanyard attachment working with out the switch being pushed in there is no current to the starter i would also check the battery, batteries are notorious for only lasting one season
1989 Acura Legend car why would a car make a spinning noise after you replace the starter and battery connection you check the flywheel it's ok battery good alternator is good sound like it winding?
When you replaced the starter, were there any spacers or shims that allowed for the alignment of the starter into the block? While that COULD be the problem, I doubt it but I thought I'd mention it. It sounds more like a problem with the replacment starter. When a starter is engaged, a gear that is normally pulled back into the starter is pushed out so that it can be in contact with the flywheel gear. If the retractable gear will not move out during startup cycle the starter motor will just wind up and nothing really happens. I suggest that you pull the starter and see if the bendix is engaging the gear. If it isn't, get another starter. For a little more information about starters, go to http://www.indiacar.com/index2.asp?pagename=http://www.indiacar.com/infobank/battery_starterassembly.htm
