0
What else can I help you with?
How do you remove the fan clutch from 93 suburban theres no nut on shaft?
the fan clutch is attached with one large nut that is part of the clutch assembly .NOTE the the cluth has LEFT HAND thread.
How do you install a shift shaft on a 2004 kx 65. Do you need to remove the clutch assembly?
I'm in the process right now. Comes out easy if the foot peg was not in the way. I will have to remove engine mounts to tilt engine to remove.
What are the different troubles that may be encountered during clutch assembly?
Linning up the clutch assembly so the pilot shaft slides in easily. If the pilot shaft does not slide in easily, start over, do not force it together by drawing the transmission in with the attachment bolts.
How do you remove the air conditioner clutch and pulley assembly on a 1994 GMC Sierra pickup truck?
Most AC compressors have a bolt in the center of the clutch unit, remove that bolt and under that you will find more threads, most are around 1/2in corse, put the large bolt into those threads and turn it clock wise, this will push against the main shaft of the compressor and jack the clutch off the shaft.
Where is the clutch slave cylinder on a 1993 Jeep Wrangler?
It is on the input shaft of the transmission (inside the bellhousing). to remove it you need to remove the transmission enough to slide the input shaft, remove the hydraulic lines that control it and slide it off the shaft.
Remove axle-shaft joint assembly 1995 ranger 4x4?
To remove the axle-shaft joint assembly from a 1995 Ford Ranger 4x4, start by safely lifting the vehicle and supporting it on jack stands. Remove the wheel and brake components to access the axle assembly. Disconnect the axle from the differential by removing the retaining bolts and then slide the axle shaft out of the hub assembly. Ensure all seals and retaining clips are removed, and carefully extract the axle-shaft joint assembly from the housing.
How do you remove the half shaft of a 1993 Chevy blazer?
by separating the lower balljoint and sway bar on that side
How do you change the ac compressor clutch on a 2001 peterbilt?
To change the AC compressor clutch on a 2001 Peterbilt, first, disconnect the battery and remove the serpentine belt from the AC compressor. Next, remove the compressor from its mounting bracket to access the clutch assembly. Use a puller tool to detach the clutch from the compressor shaft, then install the new clutch by reversing the removal process. Finally, reassemble everything, reconnect the battery, and check the AC system for proper operation.
How do you remove driveshaft to replace clutch?
The driveshaft is removed to replace the clutch by unbolting the u-joints and retaining caps on each end of the drive shaft. The shaft can then be collapsed slightly to allow for easier removal.
How do you remove the fan clutch from 1992 Ford E150 van 6-cylinder?
The 4.2 Liter and 4.9 Liter, 6 cyl engine, both have one large nut holding the clutch assembly onto the water pump. Remove the radiator shroud. You need two wrenches, one goes behind the clutch to restrain it from turning, and the other wrench removes the nut on the front of the clutch shaft. It is a two man job, with one person under the vehicle restraining the shaft, and the other person on top, removing the nut. You may have to remove the fan first, to get access. You man have to remove the upper radiator hose on some models.
How do you remove the trans-axle to change the clutch. release bearing will not release from clutch diaphragm fingers?
you have to remove the clutch arm from the top of the trans because there is a stop on the arm stopping the shaft from spinning to release fork inside from bearing.
How do you install a flywheel on a 1991 Chevy 350 GMC1500 truck?
Remove either the engine or transmission, remove the pressure plate from the existing flywheel and examine both the pressure plate and clutch plate, unbolt the flywheel from the crankshaft and remove it. If there are many miles on the clutch, don't even TRY to reuse it. Examine/replace the glan nut/pilot bushing as necessary and lubricate according to specifications. Bolt the NEW flywheel onto the crankshaft. Using a pilot shaft, install the clutch plate/pressure plate assembly. Make sure the shaft can be removed easily and that the clutch plate is centered exactly on the pilot shaft. Install the engine or transmission. If you haven't done one before, good luck.
