0
You will get a vibration in the car when they start to go. Which means they are unbalanced because of parts moving around.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you know when you need a new distributor in your car or is it possible thAT it may only need a new cap and rotor?
If the distributor shaft has side to side play it is probably worn out. If the shaft has no play just replace the cap and rotor.
Can you spray paint a lacrosse shaft?
Of course you can but it depends on the shaft type if it'll stick or not. If it's a plexi-glass harrow stick then yes it will but if it's a metal warrior stick then It might get washed away next time it rains, so pick your paints carefully to select a few that are water-proof. Also, why not just get a colored shaft?
How do you remove the starter solenoid on your 1985 Harley EVO?
I have a 85 FXWG, Dont know if the set up is the same but it should be close. There are two ways you can go about #1) Remove outer primary and the mounting bolts to the Solinoid then remove the starter, in where the starter bolted to the inner primary casing, there will be a gear that meshes with the gear on the end of the starter shaft. ( when the solinoid is pulled in) It is held in place with 1 or 2 Allen head bolts. (Can't Remember) Remove the Allen bolts and this will allow you to pull out the shaft (from the inside of the primary) that engages your starter to the Clutch. now the Solinoid has a fork that attaches to that shaft and it can be wriggle free as you pull on the shaft and pull out on solinoid at the same time. watch for shims when you pull the outer primary cover and replace them on the stub shaft when you put it back on. #2) Remove the outer primary cover and with care you can bend one side of the fork that pulls the shaft into the clutch, you will see what I am talking about this will allow you to pull the solinoid with out going thru the hassle of pulling the starter. Then when you put in the new solinoid just bend the fork back up enough that it will not fall out of place. The fork is not real easy to bend it will take some doing. Hope this helps
Is it safe to drive your car if the oil sending unit is out?
yes.if you know you really have oil pressure.
What do people use to know when an earthquake is going to occur?
eh, psychics? We don't know when they're going to occur in advance, they can only look at patterns of when faults slip or volcanoes erupt and guesstimate.
How much do a drive shaft cost for a Volvo?
Need a year and model. As is, we don't know if you're talking about a car or a semi truck.
How do you know if a drive shaft is going bad on a 1993 Chrysler Lebaron Convertable?
It will make noise underneath the car especially when you turn the wheel
How do you know if your Lexus Rx330 2004 model is AWD?
Look under the vehicle. If there is a drive shaft going from the front half of the vehicle to the back half of the vehicle then it is AWD. If no drive shaft then it is FWD. If you're still not sure after looking at it take it to a shop, they will tell you for free.
How do you know if the rear end went out and not the clutch?
You would need someone to look under the vehicle at the drive shaft while you try to move. If the drive shaft spins, but you don't move, its the rear end. No spinning drive shaft, then you have no clutch.
Do you know what equipment is required to control the speed of motor shaft rotation angle of motor shaft and reverse the direction of motor shaft?
Variable Frequency Drive
Looking for drive shaft for m43 military ambulance?
condo and sons monticello, in 47960 they have a m43 ambulance parts, i know they have or had the front and rear drive shaft for one also.,
How do you know if you have front wheel drive?
You look underneath by the front wheels for an axle shaft.
How do you know if your Buick Rendezvous is AWD or FWD?
The easiest way is to look under the body of the Rendezvous and see if there is a drive shaft connected to a transfer case on the rear wheels. If there's no drive shaft, it's FWD, if there's a shaft, it's AWD.
What drive shaft will fit on passenger side for a 3sge beam engine 1998?
I don't know you tell me.
I am installing a 4.5 inch lift on a Cherokee will i need extras driveshafts and etc or can i just toss it in and go?
If you are changing the height of the vehicle and not the length you may be able to keep the same drive shaft. However if you change the height by too much, you may have to get a longer drive shaft. Try it with the shaft you have after the kit is installed and then you will know if you need to change your shaft.
Who built the first shaft drive motorcycle?
In 1910 the Belgian arms company ' Fabrique National ' known as FN made the first 4 cylinder motorcycle with shaft drive. There were bicycles using shafts in the 1830's but this is the earliest motorcycle I know of.
Is the Polaris sportsman 400 ho truly a shaft drive system?
Yes it truely dose I work at the factory I know
