0
Just came in the house from doing just that. First remove the heat shield from the exhaust pipes. Next I found it's best to remove the upper radiator hose. ( Gives you room to work). This now gives you some room to get at the 2 starter hold down bolts and the nut that holds the main electrical wire to the starter. Also you can now take off the little plug that goes on top of the starter.Once you take off these bolts, the starter can be removed via the exhaust pipes. The new starter will go on alot faster you'll find. Mine did. Good luck! ***************** I just replaced the starter on a 1999 Galant 3.0 V6 (1999-2003): The starter motor is located on the front of the engine behind the exhaust pipe and next to the oil filter. First disconnect the battery. Next remove the flat, angular heat shield from the starter itself (1x 8mm nut and 2x 8mm bolts). Do NOT try to remove the heat shield from the Exhaust pipe - it can't be removed with the starter in place and it's not necessary anyway. Next remove the oil filter. You'll loose a few ounces of oil so be prepared for that with a drain pan and either cover the removed filter to keep debris out or replace it and remember to check the oil level later. Remove the small signal wire from the solenoid (released by pushing in a tiny lever with a finger tip) and also remove the 12mm nut attaching the positive battery cable to the starter. The starter is held in place by two 14mm bolts. On the engine (passenger) side, there is a 14x30mm bolt threading into the transaxle from the bottom of the starter. On the transaxle (driver) side, there is a longer 14x50mm bolt threading into the top of the starter. Funnily enough, I just replaced the battery two weeks ago. I suspect now that the power of a new battery burned up the worn brushes in the original starter.
What else can I help you with?
How many bolts do you have to take off to remove the starter from a 1993 Pontiac Bonneville?
17
How do you know if the starter needs to be replaced on a 1993 Nissan Altima?
Take the steering column housing off (usually held by 4 screws from the bottom) and remove the starter cap from the back of the ignition cylinder. In a Nissan, the ignition cylinder usually has a T shaped pin which turns the starter. if you can start your vehicle by turning the starter cap with a screw driver, you probably don't have an issue with the starter.
Where is the starter solenoid located on a 1993 Lumina APV 3.8L?
It's attached to the starter.
Why wont a 1993 grand marquis start from igintion but will start from starter?
Probably a bad starter solenoid.
How do you change a starter on a 1993 Buick century V6?
replacing the starter is relatively simple, what do is remove the wires from the starter solenoid which is located on top of the starter motor, and mark where the wires came from, there is a small terminal then there is a bigger terminal. oh and un hook the battery before that because it's an unpleastant surprise. then using a jack support the starter before the bolts are removed, then remove the bolts, which in most cases are 15mm, then lower the jack with the starter and put the new one one the jack. raise the jack and hook everything back up. get the starter secured and hook the wires up then the battery and turn it over. jeremy aka ccz5105
What size are the door speakers in a 1993 Mitsubishi Diamante?
5.25" see Crutchfield.com
Can a you travel from Washington state to marshall Texas with a 1993 Mitsubishi diamante?
if you stop for gas
How do you change the water pump on a 1993 Mitsubishi diamante?
Ooh, this is a fun one. The water pump is driven by the timing belt, so you have to remove and replace that to change out the water pump. ~Pengauin
Mitsubishi Diamante 1993 use freon?
yes it does r12. if you dont want to convert to the 134a. you can use freeze 12.
Do any fuses under the hood control the radio in your 1993 Mitsubishi Diamante?
yes usaly in the same cicuit as the interior lights
Where is a crankshaft position sensor located on a 1993 Mitsubishi diamante wagon?
if its sohc it doesnt have , if its dohc its behind the lower damper i think
How do you replace the starter on a 1993 Chevy Cheyenne?
Remove the positive battery cable from your 1993 Chevy Cheyenne battery. Remove the two cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.
How do you install a starter on a 1993 Chevy Corsica?
Begin by removing the positive cable from your 1993 Chevy Corsica battery. Remove the cables on the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
How do you change the thermostat on a 1993 Mitsubishi Diamante?
Drain the radiator, remove the top hose from the thermostat housing then remover the nuts from the housing. Gently tap on the housing and remove it. There's your thermostat. Take it out, put in the new one and replace everything you just took off. Refill the radiator and go.
How do you remove a starter for Chevy Camaro v8 93?
Begin by removing the positive cable from your 1993 Chevy Camaro battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. The starter will come off.
Where is the tension pull on a Mitsubishi diamante 1993?
On a 1993 Mitsubishi Diamante, the tension pull for the serpentine belt is typically located on the belt tensioner pulley. This tensioner is spring-loaded and automatically adjusts to maintain the correct tension on the belt. To release tension for belt replacement, you usually need to use a wrench to rotate the tensioner away from the belt. Always refer to the vehicle's manual for specific instructions and diagrams.
How do you remove cup holder 93 diamante?
To remove the cup holder from a 1993 Mitsubishi Diamante, start by gently prying off any surrounding trim or paneling that may be covering it. Once exposed, check for screws or clips securing the cup holder in place and remove them. Carefully pull the cup holder out of its slot, ensuring not to damage any wiring if applicable. Reinstalling is simply the reverse process, aligning it properly before securing it back in place.
