what is the year of this van 2002 or 1992?
The 1992 Saturn wiper motor is located on the firewall in the engine compartment. The wiper motor will be in the center of the firewall.
Remove winshield wiper assembly to remove altrnator,i know ive done it
Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.
first remove the window wiper arms then remove the plastic trim this will reveal the heater motor, then unclip the electrics and the unbolt the motor (on some cars you have to remove the wiper motor to take out the heater motor)
the wiper motor is mounted on the outside of the firewall, on the top-passenger side. you will need to pinch off each side of the electrical connector to release the latch and pull on the connector to remove it. The motor is attached with four 10mm bolts. Remove the bolts to free the motor from the firewall. the motor mechanism is attached to the wiper pivot rod and needs to be detached with a pair of needle nose pliers. you will need to pivot the wiper slightly to get better access to the fastening nipple. gently slide the pliers between the motor arm and the pivot rod while applying a slight prying force. It will pop out of place. To reinstall, use a channel lock type of plier and apply only as much force as necessary to the nipple/pivot rod to replace the knuckle in the boot.
It would depend on the year, make and model vehicle.
One bolt at a time-cute but not helpful
Its under the winshield wiper assembly
There is no switch. If the wipers park in the middle or at the top of the winshield you need to replace the motor. the fault is in the logic
The wiper motor bracket has a tab that can bend causing the wipers to park vertical. Either attempt to bend the tab back, or replace the wiper motor bracket itself.
removal of rear winshield wiper arm on 07 outback
In the windshield wiper motor.
Underneath the winshield cowl, drivers side
How to replace wiper motor on a 1998 montero sport mitsubishi
how do you replace rear wiper motor on a 1997 ford explorer
No, usually there is only one.
Remove the wiring harness from the wiper motor. Remove the windshield wiper arm from the wiper motor. Remove the wiper motor retaining screws. Reverse the process to install the new wiper motor.