0
Depends on the year, if it is a newer truck than the theft system will have to be relearned. turn the key on and let it sit for 10 minutes. on some vehicles this works, otherwise you need to have it done at a gm dealer.
Wiki User
∙ 19y ago
Wiki User
∙ 16y agoFirst you need to take off your horn cap. Then take a 13/16 socket to loosen the steering wheel. Take a steering wheel puller to get the wheel off. After that you need to get a lock plate compressor to push the plate down to remove the snap ring. (There is a tool for this but it can be taken off by a flat head screwdriver. Now you need to undo the screws in the turn signal switch and unscrew the hazard light button on the outside of the column. After you take out the turn signal switch there will be a screw right under the slot for the ignition switch on the inside. You need to unscrew this. Now you have to have your key in the ignition to remove the ignition switch. Turn your ignition switch either all the way forward or back to remove the ignition switch
Wiki User
∙ 18y agoyou cannot repair the switch,you must replace and relearn.gmjim
Wiki User
∙ 18y agoUnder dash on steering column. I believe it is white with a rod going to it.Two screws holding it on.
Add your answer:
Earn +20 pts
Where is the ignition switch on a 1997 Hyundai Accent and how do you change it?
changeing ignition barral
How do you unlock 1997 Mercedes Benz C230 ignition switch will not turn.?
Try jiggling the steering wheel while turning the key. Sometimes if the wheels are slights turned when you shut it off the steering wheel is pressed against the ignition switch inside the column. If that doesn't do it you probably will need a new key.
How do you remove the ignition lock cylinder on a 1997 astro van?
Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.
How do you remove the ignition switch in a 1990 Pontiac Grand Am?
The knob you pull out is attached to the switch. To get the switch out, you will have to remove the panel underneath the dash, and some of the HVAC ductwork that runs underneath. Disconnect the battery. On the back of the switch, under the dash, there will be a little button you will have to push in to get the switch's shaft & knob to release from the switch. After that is done, you will be able to pull off the trim going around the face of the dash. It should just snap on. Then there will be a nut holding the switch to the dash. Remove the nut, the switch will come out the back, and then you can unplug it. Replace in reverse of these directions, only leave the swith shaft/knob for last. It will just push back into the new switch.
Where is the Geo Metro 1997 coil ignition placed?
Firewall Drivers Side
How do you disable the factory kill switch in a 1997 Ford Ranger?
Get a repair manual for your truck, because you will need to cut the wires out of the ignition switch, and bypass the alarm.
How do you change the ignition switch on a 1997 Chevy Camaro?
You will need to remove the retaining ring from the top of your 1997 Chevy Camaro ignition switch. The ignition switch will slide out. Remove the wiring harness. Reverse the process to install the new ignition switch.
How do you replace a 97 Camry ignition switch?
1997 Toyota Camry ignition switch removal
Where is the 1997 ford escort ignition switch location?
The ignition switch is where you insert your key to start car
Where is the ignition switch on a 1997 Hyundai Accent and how do you change it?
changeing ignition barral
How do you change the ignition switch in a 1997 Honda CR-V?
In order to replace the ignition switch in a 1997 Honda CR-V, you must first unplug the ignition switch power source. Unscrew the cover panel, remove the bolts holding the switch, and pull the switch out of the column. Replace the old ignition switch with the new ignition switch, return the bolts and screws, and reconnect the power source.
Remove the 1997 c280 ignition pack?
Steps to replacing 1997 Mercedes-Benz C280 ignition switch?
What does an ignition switch do for a 1997 jeep?
It engages and disengages the lock that starts the vehicle. There are 2 parts to the switch. The ignition switch and the lock assembly.
Why does my 1997 gmc jimmy shuts off while driving?
if no warning and it just shuts down but dash lights and radio light up check ignition switch
How do you take out and install a switch ignition?
my granddaughter has a 1997 GEO prism LSI. i need to know how to remove the ignition switch
Where is the ignition switch located on 1997 Oldsmobile bravada?
The ignition switch is located inside the steering coulum below the key and tumbler.
Where can you buy an ignition switch for a 1997 Geo Metro?
www.advanceautoparts.com
