answersLogoWhite

0

what do you reset the cehck engine light patriot manual transmission 2008?

thanks for you support.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you reset the change oil light on a 2004 grand am?

To reset the light, turn your ignition to on, then press the gas pedal 3 times, then start the car. To reset the light, turn your ignition to on, then press the gas pedal 4 times then you will hear a beep, then start the car.


How do you reset the oil change light on a Ford f150?

To reset the oil change light on a Ford f150 you start by pressing the button on the dashboard. After you press the button on dashboard, it will start to cycle through liquid level checks, such as fuel level. When it gets to the oil, press and hold the reset button.


How do you I reset the tire pressure light on my 2011 Jeep Patriot?

To reset the tire pressure light on a 2011 Jeep Patriot, first ensure that all tires are properly inflated to the recommended pressure. Next, turn the ignition to the "On" position without starting the engine. Press the gas pedal three times within 10 seconds, then turn the ignition off. Start the vehicle again, and the tire pressure light should be reset. If the light persists, check for any underlying tire issues.


How do you reset change oil light on a gand am se?

After changing the engine oil, the system must be reset. With the ignition key to ON (engine not running), push the RESET button located in the driver's side instrument panel fuse block. The CHANGE OIL light will start to flash, press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.


How do you reset the oil change light on 2008 mdx?

To reset the oil change light on a 2008 Acura MDX, start by turning the ignition switch to the "ON" position without starting the engine. Press the gas pedal three times within five seconds. After that, turn the ignition off and then back to the "ON" position to verify that the oil change light has been reset. If the light is off, the reset is successful.


How do you reset change oil light on 2000 Pontiac grand prix?

turn the ignition to "Run" or where it would be once it was started, but dont start it. quickly push the gas pedal to the floor three times. the change oil light should start flashing and it will reset.


How do you reset the oil change light for a 1997 cheverlet lumina?

Turn ignition on but do not start engine, depress accelerator to the floor three times within 5 seconds, oil change light should flash 5 times, oil change light is reset if you did this correctly.


How to reset change oil now light?

turn the ignition to the run position but do not start it, pump the gas pedal 5 times til you hear a chime noise that indicates that the oil change indicator light is reset.


How do you reset the low tire pressure indicator lighton a 2010 Jeep Patriot?

To reset the low tire pressure indicator light on a 2010 Jeep Patriot, first ensure that all tires are properly inflated to the recommended pressure. Then, turn the ignition to the "On" position without starting the engine. Press the gas pedal three times within ten seconds, then turn the ignition off. Start the engine, and the light should be reset.


How do you reset the change oil light on the dashboard of a 2004 infinity qx56 after an oil change?

Start the car push the trip button until you get to engine oil and select reset and you are done.


How do you reset oil change required light 02 explorer?

start explorer press setup when it comes to engine check push RESET it says new oil push and hold reset it busses and it is reset until next oil change


How do you reset oil change light on 2013 impala?

To reset the oil change light on a 2013 Chevy Impala, first turn the ignition to the "On" position without starting the engine. Press the gas pedal three times within five seconds. After that, turn the ignition off, then start the engine to ensure the oil change light is reset. If the light remains on, repeat the process.