0
First, Honda doesn't cover this in their owner's manual (see page 291)! Very frustrating! You can do it! You need a flashlight.
1) the license plate bulb assembly (clear plastic) has "remove" on the left with an arrow and "Stanley" on the right ... slide assembly right and it will release
2) the assembly is attached to an expanding cord that you can lengthen to clear the handle ... you have to work it to clear the "H" cover but it can be done
3) looking at the back of the bulb assembly you'll see two release clips for the clear cover ... the cover releases easily
4) pull the bulb out ... there is no release and it takes a bit of effort! To grasp the bulb I used a thin rubber sheet ... note where the wires are on the bulb you removed!
5) Push in relacement bulb ... wires are up on right side
6) Replace plastic cover ... it will snap in place
7) Position bulb assembly and align with cut out in hatch ... This can be frustrating but it will align ... left side mustbe positioned first, then press right side to snap in place
8) Assembly should be flush on both sides ... You're done (after a quick test)!
What else can I help you with?
How do you replace the license plate bulbs on a Honda Pilot?
The clear covers for the license plate light bulbs have small arrows pointing in one direction. Simply push the cover to the direction of the arrows and the covers will slide off allowing for the old light bulbs to be replaced.
How do you replace the license plate bulb on a 2004 Honda cr-v?
how to replace the license plate bulb on a 2004 Honda cr-v
How do you replace license plate bulb on 2004 crv?
how do you replace a honda crv licence plate bulb on a 2004
How do you replace a license plate bulb on a 2005 grand prix?
Open your trunk the two inner bulbs are for your license plate twist and should pop right out
How do you replace the license plate bulbs on a 1998 Chevy Blazer?
push up and turn on the housing
How do you replace license plate bulb on 2008 Pontiac G8?
You need to remove the liner on the trunk lid. That will give you access to the license plate lights housing. Remove the sockets by twisting 1/4 turn and replace bulbs. Size for bulbs are 2825
How do you replace one of the rear license plate bulbs on a 2002 Buick Regal?
OPEN THE TRUNK LID. JUST INSIDE THE LID BEHIND THE LICENSE BULB CASE ARE 2 PHILIP HEAD SCREWS THAT REMOVE THE BACKING PLATE. ONCE YOU REMOVE IT YOU CAN REPLACE BOTH LITTLE BULBS. THEN PUT THE PLATE AND SCREWS BACK IN YOUR READY TO GO.....
How do you replAce license plate bulbs on 1998 buick lesabre?
If you can not remove fasteners on outside, you may need to cut a section out of the inside of trunk to get your hand by the bulbs.
How do you replace license plate bulbs 2002 miata?
To replace the license plate bulbs on a 2002 Mazda Miata, first, open the trunk and locate the license plate light assembly on the rear of the car. Use a flathead screwdriver to gently pry off the light cover. Once the cover is removed, twist the old bulb counterclockwise to remove it, then insert the new bulb by twisting it clockwise until secure. Finally, reattach the light cover and test the new bulbs to ensure they are working.
How do you replace license plate bulbs on 1998 cheve blazer?
To replace the license plate bulbs on a 1998 Chevrolet Blazer, first, open the rear hatch and locate the license plate light assembly. Use a flathead screwdriver to gently pry off the light lens cover. Remove the old bulb by twisting it counterclockwise, then insert the new bulb by twisting it clockwise into the socket. Finally, snap the lens cover back into place and check that the new bulbs are functioning properly.
How do you replace the light bulb that shines light onto the license plate on the rear bumper of a 2003 Chevy blazer?
Remove the screws that hold the covers in place. Replace bulbs!
How do you replace License Plate Bulbs on 2004 Nissan Sentra?
There are two (2) lights directly above the license plate. Each light has two (2) screws. Remove these screws and the covers. Lights pop out with little effort. Replace bad bulbs with size 194 lights. These are approx $2 at walmart or an auto parts store. Once bulbs are replaced, reattach covers with the screws and you should be good to go.
