0
What else can I help you with?
How do you change a light bulb on the fuel gauge of a Ford Freestyle?
Remove 2 7mm bolts on instrument cover plastic. remove this part exposing the 4 7mm bolts that hold in the cluster then carefully remove instrument cluster from dash. On the back of the cluster you can remove the bulbs by turning them counter clockwise and pulling them out. Bulb number 194
1998 Ford Mustang speedometer not working?
If you can"t see how fast you are going, then you need to change the speed sensor located on the transmission. If the miles are not turning, the dealer will try to only sell you a complete instrument cluster but you can change out the gear inside the cluster to make the miles start turning again. You can find the gear online.
Where are the fuses for the turning signals on a 1999 Mitsubishi Eclipse?
There are two fuse boxes in this year of eclipse as well as many other cars as well, one is under the hood to the right which hold the main crucial fuses the other is under your steering wheel on the left wall beside your pedals the fuse for your turn signals are in there. -Cody
How do you replace the dash light in your 1995 Toyota Avalon?
You have to completely remove the instrument cluster and the bulbs are removed by turning the gray colored plastic "pins"located on the back side of the cluster counter-clockwise then the bulb pulls out of the holder and the new bulb just pushes back in.The lens on cluster does not have to be removed.
1996 DODGE NEON no lights on dash at night?
First check the dimmer by turning the headlight switch knob. If that doesn't work, next you may need to replace the fuse or the bulbs that light the instruments. You will need to remove the instrument cluster to access the bulbs. If that doesn't work your instrument cluster may need to be replaced. Neons have a common problem with weak solder points on the circuit board for the instrument cluster. To access the instrument cluster, pop off the top of the whole dash with a trim stick or plastic putty knife. It is also possible for a wire in the harness behind the dash to be broken or cut, but this is unlikely unless someone has been working back there.
How do you change the instrument panel lamps on a 2002 Chevy Prizm?
Instrument Panel Lamp Procedure per Prizm Shop Manual This procedure only applies to cars with tilt steering wheels. Prizms without tilt wheels are infinitely more difficult because you have to disable the airbag system and remove the trim covers from the steering wheel. Important: The ignition switch must be in the OFF position when removing the instrument cluster assembly. 1. Tilt the steering column down in order to gain the necessary clearance to remove the instrument panel cluster trim plate. 2. Remove the two screws that secure the instrument panel cluster trim plate. 3. Disengage the two lower clips (hidden) 4. Gently remove the instrument panel cluster trim plate from the instrument panel assembly. 5. Remove the three screws which secure the instrument panel assembly, pull out the assembly carefully. 6. Mark the the 4 electrical connectors where they connect to the cluster assembly so that you remember which connector went to which socket 7. Disconnect the 4 electrical connectors from the cluster assembly 8. Remove the instrument cluster assembly 9. Remove the instrument cluster retainer with the instrument cluster lens attached from the instrument cluster case by releasing the 8 locking tabs. 10. Remove the cluster bulb socket from the instrument cluster case by turning in a counterclockwise direction. Remove the old bulb from the socket and replace the bulb. 11. Reverse the procedure to reassemble NOTE: This is such a convoluted procedure you should replace all bulbs while you are this deep into it. Trust me, the other bulbs will soon go bad. Incredibly, the shop manual does not list the part number of the bulb. Note 2: It is easier, and you are less likely to break the trim plate, if this is done while the dash is warm and therfore more flexible. Like parked in the sun for a while before starting. Also, the bulb is a #194, and you will want to get green colored "instrument bulb boots".
Is it illegal in Pennsylvania not to use turn signals?
The PA Motor Vehicle Code, § 3334. Turning movements and required signals- says that you will use your turn signals or hand signals when you are turning or changing lanes.
What are the different types of signals that can be used on a bicycle to indicate turning intentions?
The different types of signals that can be used on a bicycle to indicate turning intentions are hand signals and electronic signals. Hand signals involve extending the left or right arm out to indicate the direction of the turn. Electronic signals are typically found on modern bicycles and include flashing lights on the front and back of the bike to indicate turning intentions.
The turning signals work in a 1991 lebaron?
That is a good thing. You want the turn signals to work.
On a 2002 Chevy Prizm how do you change a light in the dashboard behind the odometer?
Instrument Panel Lamp Procedure per Prizm Shop Manual This procedure only applies to cars with tilt steering wheels. "Prizms without tilt wheels are infinitely more difficult because you have to disable the airbag system and remove the trim covers from the steering wheel. " not too sure about that...Important: The ignition switch must be in the OFF position when removing the instrument cluster assembly. 1. Tilt the steering column down in order to gain the necessary clearance to remove the instrument panel cluster trim plate. 2. Remove the two screws that secure the instrument panel cluster trim plate. 3. Disengage the two lower clips (hidden) 4. Gently remove the instrument panel cluster trim plate from the instrument panel assembly. and move it into the larger open portion of the steering wheel. Turn sterring wheel to the left and drop it out the bottom. 5. Remove the three screws which secure the instrument panel assembly, pull out the assembly carefully. 6. Mark the the 4 electrical connectors where they connect to the cluster assembly so that you remember which connector went to which socket. Unnecessary7. Disconnect the 4 electrical connectors from the cluster assembly Unnecessary 8. Remove the instrument cluster assembly Unnecessary, shift it out to one side 9. Remove the instrument cluster retainer with the instrument cluster lens attached from the instrument cluster case by releasing the 8 locking tabs. Unnecessary 10. Remove the cluster bulb socket from the instrument cluster case by turning in a counterclockwise direction. Remove the old bulb from the socket. Remove the green rubber boot from the old bulb place on new bulb, insert in socket and replace the bulb. 11. Reverse the procedure to reassemble NOTE: This is such a convoluted procedure you should replace all bulbs while you are this deep into it. Trust me, the other bulbs will soon go bad. Incredibly, the shop manual does not list the part number of the bulb. Note 2: It is easier, and you are less likely to break the trim plate, if this is done while the dash is warm and therfore more flexible. Like parked in the sun for a while before starting. Also, the bulb is a #194, and you will want to get green colored "instrument bulb boots".
How do you turn on tUrning signals on mafia 2?
Their is no Possible way :) :(
How do you check or replace the illumination lamp for the LCD odometer on a 2002 Ford Escape?
I asked the question, now I'll answer it (thanks to Tom at Jordan Ford for his help): Disconnect the battery to prevent the airbag from possibly activating. Remove two screws from top of instrument panel cover, then pull it straight toward you and remove it. Then remove four screws that hold the instrument cluster in place. Pull the loose cluster rearward enough to access and unplug three wire harness connectors. Remove the instrument cluster. Lamp sockets can be removed by turning counterclockwise about 90 degrees. Light bulbs can be pulled straight out of the socket and replaced. They are an Auto Parts Store item.
