Push spring clip forward and while pushing turn it towards the right. It should fall away to allow you to remove the bulb.
You have Hyundai redesign the dang thing. What a hassle this spring clip is. A picture would be great cause when I got my big hands in there the clip went flying.
I just posted this for another user Mine's a 96 corolla but hopefully it will be the same. Turn off ignition switch and headlight switch. Open hood. Unplug the connector (wiggle it if its tight) Turn the plastic cover counterclockwise and remove the cover. Remove the rubber cover. Release the bulb retaining spring (this is not a curly spring, its a wire clip that goes across the back of the bulb. Remove bulb. Align new bulb by the tabs around the edge. Clip spring back in place.....
Mine's a 96 corolla but hopefully it will be the same. Turn off ignition switch and headlight switch. Open hood. Unplug the connector (wiggle it if its tight) Turn the plastic cover counterclockwise and remove the cover. Remove the rubber cover. Release the bulb retaining spring (this is not a curly spring, its a wire clip that goes across the back of the bulb. Remove bulb. Align new bulb by the tabs around the edge. Clip spring back in place.....
It is a tool designed to remove spring clips.
You can change it yourself.. not really that hard.. Open the hood then look on the engine side of the headlight. There is a black cover that removes by moving the clip. Then remove the wire from the bulb. next, there is a metal clip. It is a little hard to get the clip off but once you get it off it is very easy.. Just remove the clip then take out old bulb and replace.
I think you get at it through a panel in the mud guard under the wheel arch. That is how you do it on the drivers side. Remove the little panel and there is a rubber push fit cover - take it off and the bulbs are held in with a spring clip which is a bit fiddly but not too difficult. The spring clip came out how do Iget it back in?
Pull electrical spade connector from back of bulb Remove rubber cover Bulb is held in by a spring clips on either side - feel for the clip underneath and to each side, press towards the centre and pull out Remove old bulb and put in new. Replace spring clip, rubber seal and spade connector. It may be easier to undo the two bolts that hold in the headlight first, certainly in the 06 model, the fuse box is a little close to the headlight for easy access.
Open the hood of your car. On the back of the headlight assembly, unplug the headlight wire from the bulb and remove the rubber boot. There is a metal clip that holds the lightbulb in place. It needs to be pressed in and up to remove the bulb.
Bulb replacementTo replace the headlight bulb you have to disconnect the connector that plugs into the bulb, then you have to undo the metal clip with a screw driver and after you pull the clip down the bott will come off, then you pull the headlight out .
There is a spring clip that holds them on. Squeeze the clip and then pull the electrical connector off.
puch top of clip in and slightly to the left, it will then unclip and hinge downwards, releasing the bulb.
The three clips at the top of the headlight unit hold it together, but do not give you access to remove the bulb, which occurs from behind. It can be done by feel, but the bulb is held in by an irregularly shaped spring clip, and rear access is extremely tight. Instead, you will need to remove any bolts on the top of the headlight unit (should just be the one) and the associated turn signal (should also be one). The turn signal unit has a ball/spring clip holding it in the bottom, so a good tug will free it at this point. Underneath is another bolt holding in the headlight unit, remove that as well. The bottom of the headlight is attached with a bar/spring clip, so a good tug outward (not upward) should remove that as well. I find the plastic guard surrounding the hood latch gets in the way, and it's easy to pop out, so I do. Now, pull out the three-prong plug (grasp only by the plug, never pull on the wires!) and slide the rubber boot off. The spring clip is now visible. The straight wire part is hooked under the rim where the headlight bulb is seated. Use a screwdriver to move it from under its hook and the spring rotates back and out of the way. Slide in a new bulb, reverse the process, and voila! Note: be careful never to touch the glass of the new bulb with your bare hands or get it dirty in any way, or it will burn out quickly.