0
The 1989 to 1991 Mazda 626 models, have a similar speedo cable setup. There are 2 kinds of cable. The first is a one-piece cable that runs from the transmission to the back of the speedo as one continuous length The second is a two-piece cable that has a 6 inch section from the transmission, connected to a 40 inch piece which goes to the dash. The care easily discernable because the two piece one has a large coupling on it, six inches from the transmission. To replace, simply slacken the nut on the cable from the transmission side first, using a 17mm open-ended spanner. Once off, pull the cable out of the tranny by leaning over it and gently punning it straight up. Then, remove the dash console by uncrewing all the screws. There are 4 to 5 screws, found on the underside of the dash, in front of the gauge cluster. Once off gently pull the finiher off exposing the gauge pod. It's an all in once pod of the gauges with a clear plexiglas cover. (Take care not to scratch it while handling it) The cluster itself is held to the dash by four screws. These are clearly visible in the four corners of the gauge pod. Once removed, pull the pod to you (sitting in the drivers seat) slowly. It is still connected via electrical connections. These must be unpluged so you have to reach behind the gauge pod using as little space as possible. Once unplugged, the final attachment is the speedo cable itself. It's connector is round and thick and either yellow or white plastic. There's a tab to one side that must be pressed to release it. Press the tab and pull the cable away from the gauges. ( Away from you/ towards the windsheild. ) Once it's out you can freely slacken any cable clips holding the speedo cable unser the hood and along the firewall. Pull the now free cable back through the firewall towards the engine. Handle the cable clips carefullyt and re-use them as they arent sold with the cable and are hard to source. Just repeat the process in the reverse for installation.
What else can I help you with?
How to Replace speedometer cable 1989 Toyota truck?
Speedometer cable replace 1989 toyota
Where is the speedometer cable in a 1989 Mazda 626?
Back of the speedometer, through the firewall and into the top of the transmission.
How do i replace a faulty speedometer on a 1989 Volvo 740gl?
To replace a faulty speedometer on a 1989 Volvo 740GL, start by disconnecting the car battery for safety. Remove the instrument cluster by unscrewing the screws and gently pulling it out from the dashboard. Disconnect the speedometer cable and any electrical connectors, then replace the old speedometer with a new or refurbished unit. Reassemble the cluster, reconnect the battery, and test the new speedometer to ensure it functions correctly.
What part needs to be replaced for a 1989 Nissan Sentra when the odometer and speedometer are not working?
Most of the time, the speedometer cable breaks, and you replace it. The best way to find out, is to unscrew it from the transmission, and see if you can pull the cable out from the casing. If it checks out to be good, then it will be the drive gear inside the transmission, or the speedometer itself.
1989 Mazda mx6 transmission dipstick?
auto trans have it but the manual transaxles/transmissions have a gadge under the speedometer cable and etched diagram next to it if you need more im here to answer...
How do you change the speedometer cable on a 89 Oldsmobile calais?
To change the speedometer cable on a 1989 Oldsmobile Calais, first, disconnect the negative battery terminal for safety. Then, remove the instrument cluster by unscrewing the necessary fasteners and pulling it out gently. Disconnect the old speedometer cable from both the transmission and the back of the speedometer, then replace it with the new cable, ensuring it is securely connected at both ends. Finally, reassemble the instrument cluster and reconnect the battery.
How do you fix speedometer for 1989 Honda Prelude?
To fix the speedometer on a 1989 Honda Prelude, first check the vehicle's speed sensor and wiring for any damage or disconnection. If the sensor is functioning properly, inspect the speedometer cable for wear or breaks. If needed, replace the cable or sensor, ensuring all connections are secure. Lastly, if the speedometer still doesn’t work, consider checking the instrument cluster for issues or consult a professional mechanic.
Where is the speedo cable on a 1989 s10?
The speedometer cable on a 1989 S10 is behind the steering wheel. The speed sensor is mounted on the transfer case tailshaft.
How do you lube speedometer cable 1989 Toyota truck?
Try blowing graphite down there.
How do you replace the speedometer cable for a 1989 silverado?
There is no cable....It is electric.....The speed sensor is on the transmission...Its called the VSS(Vehicle Speed Sensor)...Easy to take out and install...One bolt...Unplug the connector and remove the bolt and the sensor slides out.
How do you fix a 1989 Ford Laser ke speedometer that is not working?
probably a broken cable drive.
How do you repair the speedometer on a 1989 Z24 Cavalier?
i had the same car. its probally the cable that runs from the back of the speedometer to the trany. you have to pull out the instrument cluster. its not that hard.
