answersLogoWhite

0

From: http://www.fixya.com/support/t1942223-one_part_agitator_moves_other_part Remove Dispenser or Cap: Some models of washing machines utilize a fabric softener dispenser that resides on top of the agitator. This dispenser simply snaps onto the top of the agitator. Other styles utilize a decorative cap. To remove the dispenser, simply grab it and firmly pull up. To remove the agitator cap, insert a small flat-head screw driver into the seam between the agitator cap and the upper agitator (mover). Use a twisting or prying action to pop the cap off of the agitator. Remove Internal Debris Cap: Inside the agitator you will see a cap with a raised handle, much like that of your automobile. Simply reach into the agitator and twist the cap while pulling up. This will remove the cap and its o-ring. Remove Agitator Stud: When looking into the agitator assembly, you will notice a single nut in the center of the agitator. Use a socket kit or nut driver to remove this bolt (agitator stud). Remove the Upper Agitator (Mover): With the bolt removed you should be able to remove the upper half of the agitator (mover) by simply pulling up. Sometimes pulling up will actually remove the whole agitator assembly. If this happens, place the Lower Agitator on the floor and stand on the flat lip. Then Pull up to separate the Upper Agitator (mover) from the Lower Agitator. Remove the Cam and Clutch Dogs: When you remove the upper agitator (mover) it contains the cam and clutch dogs. Tun the assembly upside down. The cam and dogs should then come out.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What hold the cam in on a350 Chevy?

The cam is held by the 3 bolts that holds the cam gear on the block in order to remove the cam shaft you have to remove the distribitor & intake & loosen up your rocker arms & remove the push rods &lifters.


Installing cabinet door which comes first cam nut screw or washer?

ye


How do you remove a stuck cam?

In what?


How can I remove a cam lock screw?

To remove a cam lock screw, use a flathead screwdriver to turn the cam lock counterclockwise until it is fully loosened. Then, gently pull the cam lock out of the hole to release the screw.


How do you remove a camshaft off a GM 305?

take the front grill support off if the engine is in the car. then remove the plate covering the cam. then remove the cam?. it is alot easier with the engine on a stand.


How do you remove cam shaft pulleys?

with a gear puller.


Replacement keys for x-cargo sport 20?

Remove old lock from X-cargo, use a hand grinder and carefully grind off rivet holding the Locking Cam on the back of lock, remove locking cam, Go to Home depot get you a cabinet lock Model # U-9941 $4.85 a piece .place cam from old lock onto back of new lock and install screw and washer. make sure you buy 2 locks with matching key numbers . you will need a 22 mm wrench to remove Nut holding lock on X-cargo.


Where is my cam sensor on my vauxhall vectra b?

hi your cam sensor an a petrol vectra b is under the rocker cover the bit where it says ecotec remove this panel and u will c the spark plugs remove all the bolts from the rocker cover and u will have to remove the top half of the timing belt cover to access the cam sensor it is in between the cam pullies.


Where is the cam position on a 3100 engine on a 2000 Malibu?

the cam sensor is under power steering pump! remove pump then set aside,do not remove any power steering hoses, cam sensor is reachable now!! take out bolt that holds it in place,pull straight up to remove..


Do you have to remove the heads to replace cam on a 5.3 gm engine?

Yes u do to remove the lifters


Do you need to remove the windscreen to change a cam belt?

Of course not.


How does a cam shaft come out of a 2000 Chrysler cirrus?

Over head cam, remove the valve cover and timing belt