0
Add your answer:
Earn +20 pts
What is ccna3?
CCNA 3, Switching Basics and Intermediate Routing is the 3rd of 4 courses leading to a Certified Cisco Network Associate (CCNA). It deals with advanced IP addressing techniques and intermediate routing protocols.
Is it possible to use RIP V1 with default static routes?
At the foundrynet website there is detailed information on default static routes and instructions on how to activate RIP V1 defaults.Also, information on switching and routing.
What are the two methods of switching?
1. circuit switching 2. packet switching
Routing that is done without guides is known as what kind of routing?
it is known as bee routing
How does a dynamic route get into a routing table?
Routing is the process that direct a packet to choose an optimal path from source to destination. Routing is of two types static routing and dynamic routing . Dynamic routing is not done manually and uses a number of protocols , it is automatic.
Which principle does a multilayer switch operate?
It combines switching and routing
What is difference between static and alternate routing in a circuit switching network?
Static routing is fixed, alternative routing is dynamic and therefore adaptive. If a primary route is fails, static routing will not adapt and routing is lost. However, alternative routing will dynamically change in order to maintain routing.
What has the author Stephen A Thomas written?
Stephen A. Thomas has written: 'IP Switching and Routing Essentials'
What are the three valid VLAN routing methods?
Router-on-a-stickRouter-on-a-stick using trunksLayer 3 switching
What is the function of VTP in a LAN switching environment?
What is the function of VTP in a LAN switching environment? controls broadcastsstandardizes VLAN tagssimplifies VLAN managementcreates subinterfaces for inter-VLAN routing
How do Multilayer switches combine Layer 2 data switching with Layer 3 routing?
Application specific integrated circuitMPLS
What are four major components of a packet switch and their function?
input port, output port, routing processor, switching fabric
What is ccna3?
CCNA 3, Switching Basics and Intermediate Routing is the 3rd of 4 courses leading to a Certified Cisco Network Associate (CCNA). It deals with advanced IP addressing techniques and intermediate routing protocols.
What is the most high paying job for a electronics and communication engineer?
cisco networking, routing and switching telecom engineer network engineer network configuration
What is difference between routing and switching?
Switching involves moving packets between devices on the same network. *Conversely, routing involves moving packets between different networks.Switching is able to determine where a packet should be sent by examining the MAC address within the data link header of the packet (the MAC address is the hardware address of a network adapter).A switch maintains a database of MAC addresses and what port they are connected to.(operate at layer 2 of the OSI model).Routers, on the other hand, operate at layer 3 of the OSI Model.A router is able to determine where to send a packet using the Network ID within the Network layer header. It then uses the routing table to determine the route to the destination host.
How do you install router to Cisco switch?
Loaded question. This depends on the Cisco switch and it's a very technically detailed answer - unique to every switch model. The short answer is that switches that are "modular" allow you to have routing functionality inside one or more "modules" or "cards" of the switch. Some switches allow routing to occur on each "line card", other solution allow a switch to share a single "card" to do all the routing for the entire switch. Routing and switching can be configured via a single terminal interface session - known as "native", whereas some switches separate the routing terminal and switching terminal - known as "hybrid". If that isn't enough info, go to cisco.com and use their search engine to find the "installation guides" of your model.
CCIE Routing switching Mock Lab?
CCIE Routing & Switching Mock lab- 2 Days sessionInstructor: Quadrupel CCIE Instructor Harith Duration: 2 Days http://www.winnetsystems.co.uk/ccie_mock_labs.html * Same as a real time CCIE exam * Updated to match the latest trends and changes * Quadruple CCIE Instructor: Harith * Latest Cisco equipments including 6500 Catalyst Switches * Modern presentation facilities * exam preparation Tips * Assessment
