From your question I assume you are referring to a charging adapter for a piece of electronic equipment. I believe adapters also contain a rectifier that rectifies AC voltage to DC. The one I'm looking at at this moment does this.
Your thinking is correct, in that any thing that transforms the voltage to what you need is all you need for that step. But if your adapter rectifies the voltage you will need a rectifier with your transformer.
yes. your product is only going to draw 600mA of current.. so the 1200mA transformer will be ok. just make sure that you have the correct polarity on your plug. aka is the center + or -
yes
500mA = 500 miliamper 1000mA = 1 amp so 500mA = .5 amps
Yes you can. But it may damage your computers power supply.
Power = volts x amps, so your example will be 12 x 0.5 = 6 watts. (500mA = 0.5 amp) Note we don't talk of 'watts per hour', it is just watts. 1 watt = 1 joule per second
No. 0.83 Amperes = 830 milliamperes. 1A = 1000mA, it's a base-ten system, just like meters or liters.
150 mA is.
Yes, you can. Here's why. If a supply's output is rated at 12 volts DC (12 VDC) and 500 milliamperes (500mA), it can deliver a maximum of 500mA at the 12 volt rating. You want to use a 12VDC supply that is rated at 1A (1000mA). That means that the supply is capable of delivering up to 1A at 12VDC. Now the crux of the matter. Your device, that's the load on the supply, needs 12VDC to operate. Your replacement supply is rated at 12VDC. No problem. Your supply delivered a max of 500mA. That does NOT mean that your load, that thing you're powering up, actually uses all 500mA. Your load knows how much current it needs to draw. Your supply has to be rated for more than that. Your supply was rated at 500mA. It worked well. The supply you wish to use will deliver a max of 1A (1000mA). It will easily supply the current your load will use. Oh, and the polarity of the new supply must be the same as that of the old one. That's pretty obvious. Always be safe and consult an electronics specialist for electrical questions. There are a number of savvy folks working at consumer electrical outlets who can get you up to speed.
A 12v AC adapter can be use to power devices that requires 12VDC and up to 500mA. It can also be use with electrical devices that require power but do not contain internal components to derive the required voltage and power from the main power.
No because that transformer can only supply a ½ amp so it would seriously overheat if a 1-amp load was connected to it.
Using a 12v 600ma source is allowing 12 volts and 600 amps of power. If the device requires a 12v 500ma source, the larger source is acceptable. Please note that it will only be drawing on 500ma of the available 600ma.
The current rating on a charger ("1000 mA", "500 mA"), usually means the currentthat the charger is capable of supplying if it needs to. It's NOT the current that'salways being pumped out.If your 7AH battery needs 500 mA at some time during the charging operation,then a 1000mA charger is capable of supplying it.
Yes. Yes, you can replace a transformer with one that has a higher current rating. The load on the transformer should be less than 200mA because presumably that is what the circuit was designed for. Since the current through the transformer should be less than 200mA, the 500mA transformer will not be damaged. The opposite is not true. You should not replace a 200mA rated transformer with a 100mA transformer, for example. If the current exceeds 100mA, the transformer could fry.
500mA = 500 miliamper 1000mA = 1 amp so 500mA = .5 amps
p=i square x r = 500ma * 500ma = .25 * 4.7k = 1175 watts
i am not sure, BUT according to the answer in this post:Can_you_use_a_9V_600mA_adapter_on_a_9V_400ma_scanneryou need an adaptor of 9v and AT LEAST 500mA (assuming that the appliance draws 500mA)
Yes, no problem whatsoever as long as the voltages are the same. The adapter's capacity is 1000 mA and your device only requires 500 mA. The draw from the adapter is only at 50%.
Yes. As long as the voltage is the same which it is. The 800mA is the capacity that the transformer can produce safely without going into an overload state. Your original adapter was rated at 500mA which means that what ever device was plugged into it draws less that 500mA. You might notice that the new adapter is slightly physically larger. So you are safe to use the new adapter with the higher rating.
Yes, you can charge a 500mA battery with a 1300mA charger.