Your question cannot be answered, unless the power factor of the load is specified. Since true power(measured in watts) is the product of apparent power(measured in volt amperes) and the power factor of the load.
So, given your figure of an apparent power of 20 kV.A(not 'kva'*), the corresponding value of true power could (theoretically!) range from
(*The correct symbol for kilovolt ampere is 'kV.A', not 'kva', and the correct symbol for kilowatt is 'kW', not 'kw'.)
5kw = 6.25 kva becoz kva = kw/ pf if we take pf is o.8
Rating for DG set and any of electrical machines is calculated in KVA. KVA is calculated as KW/pf. One can calculate the required KVA for DG set with this formulation: (KW/pf)/load rate. For example KW=110, pf=0.8 and one loads the DG at 75%, so KVA= (110/0.8)/0.75=185 KVA.
kV is kilovolts, kW is kilowatts, kVA is kilovolt amps and kVAR is kilovolt-amps reactive. A common formula is kVA-squared = kW-squared + kVAR-squared.
For normal power factors (pf=80%), you have 0.8 kW for every kva. In general however, kW = pf x kVA. Where pf is the power factor, it is the cosine of the angular difference between the voltage and the current of a circuit in alternating current circuits.
Transformers are rated in VA or kVA. That is because the voltage is limited by the power loss in the magnetic core, and the current is limited by the power loss in the resistance of the windings. The rated voltage times the rated current gives the transformer's rating in kVA.
The same way, as you convert Appels to Carrots ........... There is a formula: KVAr = KVA / KW or cos=KW/KVA > Yes, we are treating KW, KVA, & KVAr as the 3 sides in a 90 deg TRIANGLE ! KW= vertical katede KVAr = horizontal katede KVA = hypotenuse
Multiply by Amps.
kva*cos(phase angle)
kVA = kW divided by (power factor). The power factor is the cosine of the angle between voltage and current.
To convert 2 kW to kVA in single phase, you need to know the power factor. If we assume a power factor of 0.8 (common for many single-phase loads), the conversion formula is kVA = kW / power factor. Therefore, for 2 kW at a power factor of 0.8, the result would be 2 kVA / 0.8 = 2.5 kVA.
To convert AC tonnage to kVA and kW, use the following formulas: For kVA: kVA = (tonnage x 3.517) For kW: kW = (tonnage x 3.517 x power factor). Remember to consider the power factor of the system when converting from tonnage to kVA and kW.
5kw = 6.25 kva becoz kva = kw/ pf if we take pf is o.8
It is less confusing if we capitalize the units as required. 1 kVA = 1 kW, as originated from power [W] = current [A] * voltage [V]. The 'k' means 'times 1000'. The statement can be re-written as 1000 VA = 1000 W.
To convert 'kwh' to 'kvah' you first need to measure the length of time. You will then convert this amount to hours by dividing by 3,600. You will then divide this amount by the length of time.
KVA is the unit for the apparent power i.e it's the vector sum of the true power in KW and the reactive power in reactive volt-amperage. So, to get the value of the KVA for the 30KW,just divide the active power(30kw) with the power factor of that load.
kva and kw are related as KVA = (KW/PF) pf:power factor
It depends on the power factor, which depends on the reactance of the load.For a typical power factor of 0.92, 150 KVAR translates to 383 KVA, which translates to 352 KW.Power factor is the cosine of the phase angle (theta) between voltage and current. KVA times cosine (theta) is KW, while KVA times sine (theta) is KVAR.