Theoretically, you could connect three identical lamps in star (wye) and connect this to the three line conductors. But as you asked how to connect a (single) 230-V lamp to the supply, then the answer is by using a step-down transformer.
No. you cannot connect a 415 V to a 380 V motor. in case if you want to do that, you need to increase the number of turns in all the three phases of winding as per the turns calculation.
The main application for a core type transformer is to increase voltage from a standard 240v supply up to 415v instead of using a 3 phase supply.
415v air circuit breaker acceptable value of 0.01 ohms and lessthan
In India its 415V, 50Hz.
The nominal voltage in the UK is 400/230 V. That is 400 V line-to-line (i.e. line voltage), and 230-V line-to-neutral (i.e. phase voltage). Allowable variation is +10% and -6%.
415V 3 phase is the line to line voltage. The line to neutral of this supply is 230V single phase. Therefore you use one of the phases and the neutral.
In the supply industry it refers to circuits of below 1000 volts. Common voltages used are 120v, 208v, 230v, 240v, 277v, 400v, 415v, 480v.
The single phase voltage in India is 230v when we check with the phase and the nutral single line
No. you cannot connect a 415 V to a 380 V motor. in case if you want to do that, you need to increase the number of turns in all the three phases of winding as per the turns calculation.
The main application for a core type transformer is to increase voltage from a standard 240v supply up to 415v instead of using a 3 phase supply.
The three coils are actually called UVW. They are called that because they are for the three phases of a 415v supply.
If you want to have a 3-phase service with a neutral then one way to get it is to connect the incoming three phases of a standard 3-phase service to a transformer whose secondary windings are connected in what is called a "star" (also known as a "Y" or "wye") configuration which has a neutral point at the center of the "star" or "Y".Then, to get a single-phase service, you can use just one phase and the neutral. This results in about half the voltage - actually it's 1 / 2./'3 (1 divided by the square root of three) - that you'd get across any two phases of the incoming 3-phase service.NoteA three phase service on its own does not have a neutral line. The voltage difference is measured between the phases. (No voltage can be measured between any of the phase lines and a neutral because there is no neutral line.)Any electrical equipment which uses a 3-phase service exactly as it is delivered by the power generator / utility - that is, without a neutral line - are connected in what is known as "delta" connection.
IF YOUR MOTOR HAS 6 LEADS (IN THE TERMINAL BOX) OR 9 OR 12 LEADS THERE IS NO PROBLEM. IF IT IS A BRAND NEW MOTOR THE WINDING CONNECTION DIAGRAM IS NORMALLY INCLUDED IN THE NAMEPLATE OR INSIDE THE TERMNAL BOX - T1,T2,T3,T4,T5,T6 OR U,V,W,X,Y,Z MARKINGS. DUAL VOLTAGE APPLICATION IS A NORMAL OPTION FOR MOTORS. IN THIS CASE CONNECT IT IN WYE (SOME CALLED IT STAR) CONNECTION BY CONNECTING OR COMBINING T4,T5,T6 AS COMMON OR NEUTRAL THEN APPLY 230V 3 PHASE POWER SUPPLY AND CHECK DESIRED ROTATION OR ELSE JUST INTERCHANGE ANY TWO SUPPLY LINE TO CORRECT ROTATION.AnswerJudging from the values of voltage that you quote, you appear to be referring to the UK supply system. In that case, a three-phase supply has a line voltage of 415 V and a phase voltage of 240 V. So you can simply connect the machine's controller directly to the three line conductors. (These days, the nominal voltage for UK supply is now 400/230 V although, in practise, it is still 415/240 V).
No you can't use a 415v motor in a 240 v socket.
415v air circuit breaker acceptable value of 0.01 ohms and lessthan
no
Current shall increase while you apply 415V for operating it and will decrease the rpm to a much low level.